Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging th...
This basket drive hub kit is a vital component in select washing machines, designed to connect the wash basket to the central drive shaft, enabling proper rotation during wash and spin cycles. It play...
This washer lid switch is a critical safety component designed to halt the spinning motion of the tub when the lid is opened. Its primary function is to prevent accidental contact with moving parts du...
This genuine OEM drive belt is designed to transfer power from the motor to the drum in select Whirlpool, Maytag, Kenmore, and other compatible washing machines. Operating at 115 volts and 60 Hz, the ...
This shift actuator is a genuine replacement component designed for top-load washing machines. It plays a critical role in transitioning the washer between agitation and spin cycles by shifting the tr...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
Having trouble with your freezer?s efficiency? Your GE Freezer Door Gasket might be the solution you?re looking for. This is an official replacement part designed to perfectly seal your freezer door. ...
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
$7.30
In Stock
Order now and your part arrives by Mar 19
Questions And Answers for WTW5800BW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
10 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
July 29, 2021
The lid lock comes open during mid cycle
For model number WTW5800BW0
Hello Mike, Thank you for the question. With the Lock opening during the cycle it could be defective and need to be replaced, PartSelect Number PS3497627. We hope this helps!
Have a mould smell on all the clothes after washing and drying , Is there a way to clean this up?
For model number WTW5800BW0
Hi Douglas, thank you for contacting us. Scrubbing your washer tub is a great way to deep-clean your washing machine and ensure there’s no soap or detergent scum left behind. Pour a quart of white vinegar into the washer tub with 1 cup of baking soda, and use a stiff nylon brush to scrub the interior. Then run a wash cycle on the hottest temperature and heaviest laundry load settings. You will also need to clean the gasket. Apply vinegar to a paper towel and wipe down the inside of your gasket to kill any buildup that might be causing bad smells. We hope this information is helpful.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Luis
May 29, 2023
Washer is shaking s lot...what can be replace to stop it to shake?
For model number WTW5800BW0
Hi Luis, thank you for reaching out. Based on our understanding of the issue, we would suggest that you make sure the load is balanced inside the tub and that the unit is balanced. If that is not causing the issue, then you may need to check the suspension rods, part number PS11703287, as they are most likely faulty and may need to be replaced. We hope this helps!
having trouble pulling the strike out to replace the new one instructions please
For model number WTW5800BW0
Hello Norma, thank you for your question. The instructions that will help you replace the strike. 1. Push a small screwdriver into the hole of the lid strike to release a locking tab. 2. Turn the strike anticlockwise. 3. Pull the strike out of the mounting hole. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer faile
... Read mored which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform
... Read moreation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
