Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
Introducing the Tub to Pump Hose, a genuine replacement part designed expertly by GE. This invaluable accessory serves a crucial functioning role, enabling used water to efficiently journey from your ...
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This part senses how much water is in the tub and allows it to reach the desired level. For example: A little water equals little pressure and a lot of water means more pressure inside the switch.
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dave
February 14, 2020
Can drum suspension be adjusted stiffer. Present problem of unit shutting down for out of balance alarm we're not doing anything different than before and it will do a load as out of balance 50% of the time.Unitis approx 10-12 years old
For model number WPGT9360E0PL
Hi Dave. There is no adjustment sadly, you may have to replace the suspension assembly's. Thank you for your question and good luck with your repair.
Need a replacement for the detergent holder, left side has crack in it
For model number WPGT9360E0PL
Hello Kenneth, thank you for reaching out. The part you are looking for does not come separately. It comes as a part of the detergent box assembly, part number PS12343534. If you need help placing an order, customer service is open 7 days a week!
First I unplugged the washer. I removed the back of the washer and located the pump.I removed all the water from the pump, then I removed the hoses from the pump. I removed the wires from the pump and removed the two screws holding the pump in. I replaced the pump and reconnected everything. It works like new. The pump was the exact same
... Read morething ge sells but it cost a lot less.
Well replacing the pump went fine. I even did a trial run on a rinse and spin cycle and it worked great. Then i ran another cylce of clothes and walked away thinking all is well. Much to my surprise when I went to go through the utility room it was flooded. I did some inspecting and realised that I had put a hose on backwards. LOL. The go
... Read moreod thing was that after I fixed the hose all worked well and haven't had any trouble since then. Your company was the cheapest price I found and the quickest delivery. Thank you so much for your help. Sincerly, Chris Lewis
Disconnect power and water lines. Lay the washer on it's back. Remove the nut (300) and washer (305). Rock the motor rotor (215) back and forth while pulling until it comes off the splined shaft. Remove the 3 bolts from the coupling assy (345). Remove the broken coupling (340) . Apply plastic grease to internal spline and gear teeth
... Read morebefore reassembling in reverse of above. The machine is engineered to work on easily, however, I would not have needed to work on it if they had made the coupling assembly out of metal. The plastic gear fatigued at the internal spline and cracked apart after only 3.5 years of use.
