Models
>
WJRE5500GW
WJRE5500GW General Electric Washer - Overview
Sections of the WJRE5500GW
[Viewing 1 of 1]Keep searches simple, eg. "belt" or "pump".
Tub Dampening Strap
PartSelect #: PS271100
Manufacturer #: WH1X2727
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash c...
$9.61
In Stock
Drain Hose
PartSelect #: PS890597
Manufacturer #: WH41X10096
The drain hose is black in color and made of flexible material. This is a part for your top-load washer. The hose measures 57 inches long. This part moves the water out of the washer and into the drai...
$27.09
In Stock
Dual Action Agitator
PartSelect #: PS1482519
Manufacturer #: WH43X10034
This is a dual-action agitator for a washer. It is an OEM replacement part that is sourced from the manufacturer. The agitator tosses your clothes to clean them efficiently. This plastic dual-action a...
$75.31
In Stock
Drain Pump and Motor Assembly
PartSelect #: PS8768445
Manufacturer #: WH23X10030
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If you notice that your washing machine will not drain, there is...
$72.45
In Stock
Tub Seal
PartSelect #: PS4704237
Manufacturer #: WH02X10383
The main tub seal is located between the transmission and the outer tub. Its the primary water seal in the outer tub for the transmission-shaft. If your washer is leaking during the fill cycle, or at ...
$16.73
In Stock
6-Rib Drive Belt
PartSelect #: PS1482278
Manufacturer #: WH01X10302
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
$25.75
In Stock
Agitator Coupling
PartSelect #: PS1482517
Manufacturer #: WH43X10032
Bolt not included. This part connects the transmission drive shaft to the agitator base.
$25.63
In Stock
Lid Switch with Wire Harness
PartSelect #: PS1482372
Manufacturer #: WH12X10334
This lid switch with wire harnesses is used in washing machines. The pin on the lid switch pushes onto the lever of the switch to communicate to the machine that the washer lid is closed. If your wash...
$53.87
In Stock
Start/Stop Button
PartSelect #: PS268476
Manufacturer #: WH01X10088
This is the start/stop button for your washer. If your washer will not start after the button is depressed, you may need to replace it. However, you may also want to check your door switch, because wh...
$18.92
In Stock
Socket Rod Support - White
PartSelect #: PS268394
Manufacturer #: WH01X10001
This part is a replacement socket rod support for your washer. The socket rod support is found at the top of the washer frame in the front part of the washer. It supports the suspension rod, so the ro...
$12.61
In Stock
Screw - Black
PartSelect #: PS268950
Manufacturer #: WH02X10002
This screw is sold individually.
$8.06
In Stock
Rod and Spring Assembly - Green
PartSelect #: PS960673
Manufacturer #: WH16X10057
This part helps center and support the drum, transmission and motor assembly.
$44.50
In Stock
Questions And Answers for WJRE5500GW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WJRE5500GW
[Viewing 9 of 9]Leaking
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
washing machine would not go through all cycles or agitate
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.
Parts Used:
-
Brian from Millerplace, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
226 of 285 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
machine would not drain all other functions seemed o.k
Aside from getting the wet clothes and most of the water out,the toughest part of the job for me was to figure out how to get inside the machine. I nearly wrecked the thing trying to lift the top panel. After some frustration I removed the star-type screws on back of the control panel and found, tucked away neatly, the documentation/parts
... Read more
list complete with instructions on how to remove the FRONT panel. Once I got inside it was easy to locate the pump. I ran the drain cycle for a moment to see if the pump turned at all. The original had an exposed fan so it was easy to see that indeed the motor was not turning. I inspected all the hose and electrical connections to make sure I had the tools I'd need and the savvy to replace the part(s) if I could locate them. I'm not much of a web-head, so I was a little surprised when I typed G.E. appliances and the search took me to partselect.com where I was pretty much coached through the procedure before I even ordered the part. The box arrived ahead of schedule (yay) and when I looked at the pump it didn't look much like the one I was replacing. But then I realized it was the same thing just ten years more advanced. I used a small pair of vise grips to pinch and lock the pipe clamps open. I know there is a plier made for this, but... Anyways, after loosening the clamps and sliding them away from the pump I pulled the hoses off and let the last of the rinse water still in them run down my shirt sleeve to my elbow. (optional, not recommended) Thus refreshed I then rummaged through my socket set and found what I needed to remove the 2 sheet metal mounting screws and disconnected the 2 power leads. I removed the faulty pump and proudly showed it to my wife. Unimpressed, she asked how much longer. I quickly reversed the procedure to install the new unit and confidently piled in a load of laundry. The cycle completed just fine and has done so since. I will and have recommmended partselect.com to friends and will use it again for sure.
Read less
Parts Used:
-
douglas from danby, VT
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
85 of 87 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken drive belt
To diagnose, first I unhooked the washer: power, water supply, and drain pipe. I then slid the washer out, laying it on its front. With nutdriver, I unscrewed two screws that held the other end of the drain tube and removed it completely. Then, again with the nutdriver removed 4 screws from the back near the legs, two in between the leg
... Read more
s in the middle, and approx. 4 to 6 on the bottom. This let me pull the bottom off partially to access the motor area. (I did did not take the bottom completely off, only about 2/3 off and let it bend over, as it was flexible tin) The belt was broken. After receiving the new belt, I positioned it between the pulley and the motor and between the drum and the big pulley. Then I rotated the big pulley, pulling the belt onto it as I rotated. At the same time, as I rotated, I pulled the other end of the belt on to the little pulley. Once it was on, I would put pressure on it as I turned the pulley, to jump the belt to the appropriate grooves on the little pulley. Note: the replacement belt had been modified, so it had one less groove than the pulley. I would have known this if I had read the insert that came with the belt first! Anyway, this was not a problem, only a design change. Also it was important to start the belt on the inside, so if it slipped, you didnt loose your bite. Total diagnostic, repair, and reassembly time: 30 minutes plus or minus. I had read other online forums that said you had to loosen the motor, etc. And I do know some type of a belt installation tool was offered on line, but I got along fine with my installation method. An extra set of hands would have been helpful, but not necessary.
Read less
Parts Used:
-
jon from barry, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
91 of 110 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!