All Installation Instructions for Whirlpool Range WFC150M0EB2

stove top got hot when using large pans

Removed the existing element and replaced it with the new one.

Parts Used:

Albert from Bryant, SD
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Side trim broke

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

Parts Used:

Side Trim - Right Hand Side

Paul from Adamsville, TN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

corroded, rusted drip bowls

replace

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Noah from Richardson, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

8 Inch electric burner not getting hot

I determined the problem by swapping the 8 inch burner with a 6 inch burner. the 8 inch got hot when connected to the 6 inch wire harness. This told me that the 8 inch burner was good. The 6 inch failed to get hot so I determined the next logical thing was the power to the 8 inch burner. I used a multi meter to determine that power was getting into the control unit but no voltage was getting out. The controller was bad. I ordered a new controller and after unplugging the stove, replaced the controller in about 10 minutes. (Critical part of repair is to unplug unit from wall -220 volts!)

Parts Used:

Infinite Switch - 8 Inch

John from Dover, NJ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

Bottom Door Trim Rusting

I remove bottom trim which is held on by 3 screws and try to install new bottom trim, did not work well. I then remove yop handle assem. Then the door glass which you need to clean after. Then install the new bottom trim then insert the glass into the new bottom strip using masking tape to hold the glass and side strips in place prior to installing the the top handle piece which is held on by two screws. Not a hard job to do.

Parts Used:

Range Trim Lower (White)

Dennis from Grimsley, TN
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers

Was this instruction helpful to you?

Drawer Glide Snapped Off And Broke

Snapped in the new drawer glide. Took less than 5 minutes.

Parts Used:

Drawer Glide Kit - Black

PATRICIA from GEORGETOWN, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Heating element would not get red hot

Replaced Infinite control switch in just a few minutes. Unfortunately the new switch had a lose terminal that was not supposed to be in the switch that came from the factory that way. I connected the switch, turned it on, and it instantly shorted the switch out. At that point the lose terminal was real easy to see.

Parts Used:

Infinite Control Switch, 6"

James from Lewisville, NC
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

Was this instruction helpful to you?

rusted drip bowl

remove burner by hand and remove old drip bowl replace with new bowl inspect burner for ware and insert back into slot.

Parts Used:

Drip Bowl - 8 Inch

kyle from Schwenksville, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Drip Bowl beyond cleaning

Removed old bowl and dropped in new one!!It looks great - the cooktop is probably 30 years old.Your serviceperson was courteous friendly and very rapid.This actually is the second replacement but I was pleasantly surprised that the part was available. Thanks!!

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Ann from Memphis, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Two drip Bowls needed to be replaced

No tools needed. And it's always great to be able to replace parts on my VERY old counter-top range. It still works very well, and now it also looks great. Delivery was amazingly fast, too! Thanks!

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Robin from Boca Raton, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

I had a power serge and it burned the Plug at the termial block and melted a few wire.

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Parts Used:

Range Terminal Block

Robin from Vanderbilt, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

Was this instruction helpful to you?

Left front 8 inch burner knob control stop regulating heat temprature.

I purchased a new infinite control switch 6". and replace the old one.

Parts Used:

Infinite Control Switch, 6"

Alfred from Ann Arbor, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

Was this instruction helpful to you?

oven temperature did not stay as set

changing the part itself was easy, but the sheet metal covering the whole back of the oven was difficult to remove because of some screws that were stripped. The new sensor solved the problem.

Parts Used: