All Installation Instructions for Whirlpool Range WFC150M0EB1

Bake element was broken

Remove the old part and install the new part.

Parts Used:

Oven Bake Element

Range Screw (Grnd Wire / Back)

Alexander from LINCOLN, NE
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

8" surface element stayed on high.

Pulled range out from wall, unplugged AC, unplugged infinite switch, plugged in new switch, broke off end of stem, plugged AC in put range back and tested.

Parts Used:

Infinite Control Switch, 6"

Surface Burner Element Switch, Large Burner

Donald from STOCKTON, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Front glass shattered, side trim broke and lower trim bent beyond repair

Followed the YouTube video and did it the correct way they showed. Note: side trim goes under the glass.

Parts Used:

Outer Door Glass - White

Range Trim Lower (White)

Daniel from CEDAR SPRINGS, MI
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Dual burner would go to highn heat.

Watched video & did just guy in video did. Very easy job & the burner works like new.

Parts Used:

Infinite Control Switch, 6"

LOUIS C from GRAND JCT, CO
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

You

Pleaae prepopulate the manufacturer and part i purchased. I fix a lot of appliances so cannot expend the effort to decipher this.

Be well.

Parts Used:

Vent Trim - White

Ron from CARIBOU, ME
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

It was a rather simple fix--just replacing burner pans

Problem I had was finding the right ones to fit the stove top. Burner pans that tell you will fit most stoves, do not. After I had paid over $20.00 for some that did not fit, I got on the internet, found you, ordered the replacement parts and had them within a few days. Put them in and there you go. A perfectly happy me and a nice looking stove again.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Vicki from Jefferson, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Heating element, broken

Unplugged appliance, removed the 2 screws that mount element. Unhooked the electric wires,with pliers.
Connected, the wires to new element replaced the 2 screws. And was done in about 9 minutes.

Parts Used:

Oven Bake Element

Frank from COLUMBIA, TN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Electric Stove Burner was working unreliably

pulled out the old burner, plugged in the new burner. Turned on the power and it heated up very quickly.

Parts Used:

Surface Burner - 8 Inch - 2600W

Jacqueline from Austin, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Burner would stay on when switch set to low heat

Unplug and pull out range.
Unscrew the back of the range with Phillips #2.
Unplug wiring harness from switch.
Unscrew the switch from the front of the range with P2 driver.
Install and plug in new switch.
Remove the spring steel knob retainer from shaft.
Cut off extra knob shaft with dremel to match others (there is a narrow segment at the proper length).
Reinstall knob retainer, knob, and range panels.

Parts Used:

Surface Burner Element Switch, Large Burner

Casey from WARBA, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Old lower element fell apart

1. Unplug the power
2. Unscrew the two screws that hold the element
3. Pull the element out a little to expose the wires.
4. Gently pull off each wire (best done with needle nose) MAKE SURE THE WIRES DONT FALL INTO THE BACK OF THE OVEN.
5. Firmly seat wires back onto new element and replace screws
6. Bake stuff!

Parts Used:

Oven Bake Element

Matthew from MIDDLETOWN, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven not reaching temperature

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

Parts Used:

Oven Sensor

Marsha from Clermont, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Baking element had burned into

The video was very helpful.

Parts Used:

Oven Bake Element

Rebecca from LANCASTER, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Replaced screw

By hand screwdriver

Parts Used:

Range Screw

Screw

Judith from SALEM, OR
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven bake would not heat up at all.

Very simple.
Remove 2 mount screws using a #2 phillips screwdriver.
Pull the element out to expose the 2 wires.
Using pliers, slip both wire terminals off the existing element.
Push wires onto the new element and install both mounting screws..
Done!

NOTE: The existing element showed no exterior signs of being bad.
The damage must have been internal.

Parts Used:

Oven Bake Element

Wilton from CANYON LAKE, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Replacing the bulb in the freezer side

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Parts Used: