All Installation Instructions for Whirlpool Range WERE4100PB0

Door bottom trim piece was rusty

Remove three screws, slid old trim piece off door. Slid new trim in place. Used ice pick to align screw holes and replaced screws. Total time about 15 minutes. Tip: used a bead of silicone sealer on the new trim strip to prevent moisture from causing new strip to rust.

Parts Used:

Range Trim Lower (Biscuit)

Dennis from Dunnellon, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Bad element replacement

Took off top and pulled out old element and plugged in the new one

Parts Used:

6" Surface Element, 1200 W

Thomas from Warren, CT
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers, Socket set

9 of 17 people found this instruction helpful.

Was this instruction helpful to you?

light bulb in water ice freezer door went bad

I didn't. Don't know how to get to light bulb to change it for this specific model

Parts Used:

Light Bulb - 40W

Carl from RIVERSIDE, CA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

8 of 14 people found this instruction helpful.

Was this instruction helpful to you?

dropped stove forward, handle broke and trim around it also broke.

Unsrewed what was left of the trim and oven handle. Just 4 screws total, then replaced the 2 screws of the trim and the 2 screws on handle.
Finished! Replacement parts fit perfect!!! Thanks a milliion!

Parts Used:

Range Door Handle

HERLIN from BOERNE, TX
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

The heating coil was no longer working.

My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.

Parts Used:

Oven Bake Element

Amanda from Midwest City, OK
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Burner Element did not work

Shut off breaker. Remove a total of 3 screws attach wires, replace screws, turn breaker on. Done!

Parts Used:

ELMNT-SURF

Paul from Reedsburg, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

7 of 12 people found this instruction helpful.

Was this instruction helpful to you?

Bake element was taking time to warm up

Wire connection was damaged, replaced end piece

Parts Used:

Oven Bake Element

Jean-Claude from Miami, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

2nd 8 inch burner switch in a little over a year to not always hold selected tempurature.

As a former appliance repairman, the installation went just like the repair instruction video.
Just use care not to scratch anything and clean behind the appliance and cabinet walls, etc. It's worth a hug and a piece of pie!

Parts Used:

Surface Burner Element Switch, Large Burner

LELAND from HERMISTON, OR
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

I broke a piece of the trim and had to replace it

took the handle off, replaces the side trim piece and replaced the handle. Very simple!

Parts Used:

Side Trim - Right Hand Side

Gregg from SOUTH BEND, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Oven sensor was not regulating heat set for oven

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

Parts Used:

Oven Sensor

Linda from SAINT CLOUD, MN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

element went out on the stove

My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's

Parts Used:

Oven Bake Element

christopher from harrisburg, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Loose terminal caused block to overheat and break

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Parts Used: