Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This Whirlpool Dryer Repair Kit is a convenient solution for fixing noise and drum movement problems in 27-inch dryers. Compatible with models from Whirlpool, Kenmore, Maytag, and more, the kit includ...
The filter collects lint during the drying cycle. This filter is 12 1/2 inches wide and 10 1/2 inches deep. Replacing the lint filter is an easy repair which requires no tools. When replacing the lint...
This replacement door catch is for your dryer door. If the catch is broken and the door will not stay shut, the dryer may not turn on. Use a putty knife to pop out the existing door catch by the locki...
This dryer thermistor is a genuine replacement component designed to monitor and regulate internal temperature in Whirlpool dryers. Mounted on the blower housing, it plays a critical role in controlli...
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pul...
If your washer shakes or vibrates loudly when it reaches its max speed, check that the leveling legs are even. To ensure that the washer is firmly on the ground using all four legs, adjust the legs so...
This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is do...
This 10-watt clear incandescent light bulb is designed to provide reliable interior illumination for household appliances such as dryers and refrigerators. Measuring approximately 2 inches in length, ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jonathan
January 12, 2024
Does anyone have a link to a video on how to replace the belt?
For model number WED8200YW0
Hi Jonathan, thank you for writing in. Our research has found a video of a similar model for replacing the belt, part number PS11746374. They are mostly the same procedure. We hope this helps.
Dryer shut off in mid cycle and is reading “sensing”. Can’t get it to run in any setting. Help
For model number WED8200YW0
Hello Bill, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: thermal cut out kit, internal bias thermostat, heating element, and main control board. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!
Did this question help you?
Thank you for voting!
Mark
October 5, 2022
What is the part # for this dryer that the lint filter goes into. What is its name? It has two metal sensor strips also.
For model number WED8200YW0
Hello Mark, thank you for contacting us. We have researched the model you have provided and have found that the part you are looking for is part number PS12114312. If you would like assistance placing an order, please contact customer service. Good luck with your repair!
Check vent light sensor comes on sometimes.Vent pipe has been cleaned, and inside has been cleaned.Does this sensor go bad , and what is the part # can't find it
For model number WED8200YW0
Hello Lance, thank you for getting in touch. Based on the description that you have provided, we have found that the airflow in your dryer is restricted. It seems like the issue is most likely with the lint filter, part number PS1491676. If it is not clogged and working fine, you may need to replace the control board, part number PS11754079. We hope this information helps!
My dryer turns on and the "sensing" indicator lights up. The dryer won't begin the cycle but the timer will count down.(I assume I need to replace that kit as well so would like to knock out both repairs in one shipment.)
For model number WED8200YW0
Hello Scott, thank you for asking. Based on the description that you have provided, we would recommend checking the belt switch, part number PS11754411, to fix the issue. We hope this solves your problem!
After a few years of slamming the dryer door (at least that is what my husband says), the catch on the dryer door broke. Using pliers (I used needle nose) squeeze the outer edges of the catch together (vertically). With it compressed, it should slide out easily. My husband had jacked with ours prior to the repair, so the broken piece i
... Read moren the door was actually sideways and would not fit through the hole. Using a screwdriver, I pushed that piece into the door (it lives in the door somewhere now). I was then able to slide out the rest of the old catch. Compress the new catch and insert it into the hole in the door. Push it in until it clicks into place. DONE! Happy Drying!
The issue was the idler pulley. First I began opening up the front panel based on a youtube video but soon realized the model was slightly different and required a lot more items to remove. I saw the pulley in the back with nothing in the way so I put the front panel crap back on and removed the rear panel. There it was, very simple to re
... Read moremove and replace. I'm not looking forward to drum rollers though. Hopefully they're aren't as difficult as they appear.
