Models > WED8200YW0 > Symptoms > Too hot

Parts That Fix Whirlpool Dryer WED8200YW0 Too hot

Too hot is a commonly reported symptom for the WED8200YW0 Whirlpool Dryer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your WED8200YW0 Whirlpool Dryer that will fix Too hot. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!

1 Thermostat, Internal-Bias
Fixes Symptom 71% of time
Thermostat, Internal-Bias – Part Number: WP8577274
★★★★★
★★★★★
30 Reviews

Rated by 30 customers 

  

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

The internal-bias thermistor (Thermistor, Dryer Thermister, Dryer Thermistor) prevents the dryer from overheating by monitoring and controlling the temperature of the inside of the dryer drum. It is located on the blower housing, next to the thermal fuse. If your thermistor is defective, drying time could be prolonged or you could get a fault code. You could also notice your dryer overheating. You can test the outlet thermistor on a multimeter, it should read 10Kohms (10,000 ohms) of resistance at room temperature. It can tolerate 10% fluctuation. If your reading indicates the part is defective, it will need to be replaced. This model is white plastic. It is sold individually.

$ 47.74
  In Stock
PartSelect Number PS11746740
Manufacturer Part Number WP8577274

Replacing your Whirlpool Dryer Thermostat, Internal-Bias

Replacing your Thermostat, Internal-Bias

Customer Repair Stories

Dryer turns off after 1-2 minutes

I tried to follow directions followed by others on this site after diagnosing the problem via suggestions provided by users. I have a Whirlpool Duet dryer from 2002. We've had problems since moving about 3 years ago. I removed the front panel (lower) by unscrewing the two bottom screws (1/4" sheet metal screws). Then I took out the lint screen and the metal tube/contraption immediately beneath to get access to the area where thermistor is located. See the drawing/chart to help you locate this. It's really easier than it seems. Make sure you have the chart/drawing for your model - it makes difference! The thermistor came out pretty easily with a nutdriver that has a swivel offset shaft. Ask your hardware store tool dept. about that one. Put everything back in reverse order of course and test either with/without the front panel re-attached. In my case it fixed at least part of the problem. I was able to get clothes almost dry with most settings but I have yet to install the moisture sensor to see if that helps in addition to the internal-bias thermistor. I am the kind of person that does one thing at a time so at least I now know the thermistor was bad. Good luck and hang in there with your own repair. It's a lot cheaper even if it takes you longer to do than a pro.
Read less
  • Dixon from Santa Fe, NM
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
19 of 21 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Unit would shut down in the middle of cycle and flash E1 trouble code

Had to remove the back of unit to access the area of subject part by removeing 12 to 14 screws also the gas line had to be removed. Two screws held the part in place. Unit now runs normal.Saved alot on repair costs!!!!!
  • Jim from Tucson, AZ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
30 of 40 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2 Moisture Sensor
Fixes Symptom 11% of time
Moisture Sensor – Part Number: WP3387223
★★★★★
★★★★★
13 Reviews

Rated by 5 customers 

  

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is done, you may need to replace the sensor. You will find the moisture sensor behind the lint screen. Be sure to disconnect the power source from the dryer before you begin this repair. Note: Some model's require two sensors, please order quantity needed. Sensor only, harness is not included. This part is sold individually.

$ 10.72
  In Stock
PartSelect Number PS11741408
Manufacturer Part Number WP3387223

Replacing your Whirlpool Dryer Moisture Sensor

Replacing your Moisture Sensor

Customer Repair Stories

Hard to reach the screws inside the dryer They were on the door side of the dryer and hard to reach, especially if you are a abig guy.

Removed the dryer door, unscrewed lint vent.
  • Lucy from CHADDS FORD, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Moisture sensors need replacement

Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor.
Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in handy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.
Read less
  • Jack from JONESBORO, AR
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
14 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
3 High Limit Thermostat
Fixes Symptom 9% of time
High Limit Thermostat – Part Number: WP8557403
★★★★★
★★★★★
2 Reviews

Rated by 3 customers 

  

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

This authentic OEM high limit thermostat is made for your dryer. It is an important dyer element, because it will automatically shut off the heating element when it overheats. Be sure to disconnect the power to your dryer before you begin this repair.

$ 97.00
  In Stock
PartSelect Number PS11746386
Manufacturer Part Number WP8557403
4 Disposable Thermal Fuse - Two Terminal
Fixes Symptom 6% of time
Disposable Thermal Fuse - Two Terminal – Part Number: WP3390719
★★★★★
★★★★★
12 Reviews

Rated by 25 customers 

  

Easy 

30 - 60 mins 

Ratings submitted by customers like you who bought this part.   

This part attaches to the exhaust duct of your clothes dryer.

$ 17.97
  In Stock
PartSelect Number PS11741444
Manufacturer Part Number WP3390719

Replacing your Kenmore Dryer Disposable Thermal Fuse - Two Terminal

Replacing your Disposable Thermal Fuse - Two Terminal

Customer Repair Stories

The dryer stopped working and would not start.

After unplugging the dryer, I removed the bottom panel in front. Remove the the filter inside the dryer and remove the filter housing below. There you can see the thermal fuse on the air duct, its white with two blue wires. You can check it with a ohmmeter after removing the wires. If its open its bad. Its held in place with two sheet metal screws. After replacing the thermal fuse the dryer worked fine. However I would suggest cleaning the air duct and the outside discharge opening. Hope this helps.
Read less
  • kevin from Saint Augustine, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
20 of 22 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!

Dryer wouldn't turn on

Removed the back of the dryer taking off the screws. Found the disposable thermal fuse. Unplugged the 2 blue wires connected to it. Removed the screws holding the part in. Replaced the old part. Reattached the blue wires. Put the back on the dryer. And voila! That simple!
I'm a 39 year old woman with absolutely no patience for tedious jobs, but this was so easy I felt good about doing it. And felt even better for saving lots of money by doing the repair myself.
Read less
  • Olive from Williamsburg, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
49 of 64 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
5 Thermal Cut-Off with High Limit Thermostat
Fixes Symptom 4% of time
Thermal Cut-Off with High Limit Thermostat – Part Number: 280148
★★★★★
★★★★★
6 Reviews

Rated by 2 customers 

  

Easy 

1- 2 hours 

Ratings submitted by customers like you who bought this part.   

The thermal cut-off (fuse) is meant to trip at a higher temperature than that of a high limit thermostat. This is a one time use fuse, so when it does trip, you must replace it. The hi-limit thermostat acts as a safety mechanism that keeps the dryer from overheating. Once the dryer temperature reaches a certain point, this piece will shut down power to the heating element.

$ 58.88
  In Stock
PartSelect Number PS991443
Manufacturer Part Number 280148

Customer Repair Stories

My dryer was not getting hot.

The first thing I did was to watch the video from Part select on How to change thermostat cut off switch and the high limit thermostat fuse.I did not have a meter reader I just brought the thermostat cut off kit for about $ 32.00 dollars from part select and replace both part's and my dryer still was not getting hot so back to part select video's I looked up the video on replacing the heater element and I ordered one for about $ 97.00 with shipping I replaced it and put it back together and it worked it took just a few hours . I would like to give Avery special thank to part select for the video help and for having the parts for a great price again thank you so much.
Read less
  • Ronnical from Napanoch, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Back to Top