This OEM gray Dishwasher Lower Dishrack Wheel Assembly is a plastic kit that allows the rack to slide in and out of the dishwasher easily. If it breaks or becomes damaged. sliding will feel difficult....
This part is a door balance link kit, also sometimes known as door cable or door spring cable kit, that helps support the door as it opens and closes by connecting to the dishwasher door hinges. The k...
This authentic Dishwasher Upper Rack Adjuster Kit with white wheels is a kit made up of primarily plastic and metal components, and which will require a screwdriver to install. This kit comes with all...
The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
The mounting bracket is sold individually, without screws. This part secures the upper side of the dishwasher to the underside of the counter or cabinet to prevent the dishwasher from moving, shaking,...
The tine pivot clip, also known as the tine row pivot, is used in dishwashers and is located in the upper dishrack. At around 3 inches in length, the clip is used to keep the tine row in place in the ...
Also known as rack adjuster. Sold individually.
This is an original part from KitchenAid, Kenmore, Whirlpool, Jenn-Air, and Maytag for use with Dishwashers. The dishrack adjuster arm positioner clip...
Sold individually.
This dishrack adjuster is for dishwashers.
Dishrack adjuster lets you change the height of the dishwasher's upper rack.
Wear work gloves to protect your hands when installing this part.
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Fred
December 29, 2019
My upper rack right side front wheel has broken away from carriage. It is part #4 in the diagram, but i do not see it in the parts list
For model number WDTA50SAHZ0
Hello Fred,
Thank you for your question. The right side wheel is only available through the rack adjuster kit for your model under part PS10065979 that comes with both wheels for each side. We hope this helps!
White wheels have broken off both sides of the housing on upper rack. What part number do I order? Thanks.
For model number WDTA50SAHZ0
Hello Janet, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS10065979. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Hello, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11745496 for the Mounting Bracket. We hope this helps.
Dishwasher won't heat the water. I've already replaced the heating element and that's not the issue. Where do i look next?
For model number WDTA50SAHZ0
Hello, Thank you for your question. The next part you will want to look into is the thermostat- Part Number: PS11750035. We hope this helps, good luck with this repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Carolyn
October 4, 2022
Water leaking from under the door
For model number WDTA50SAHZ0
Hello Carolyn, thank you for your question. We have researched your model and found that the issue is probably with the door seal, part number PS11731683. The seal forms a watertight barrier between the door and the dishwasher tub, deterring water from escaping during a wash cycle. If you require assistance to place an order, please contact customer service. We hope that helps!
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.
2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.
3. Make sure you have enough slack in the water input line and electrical wiring that you can pull the dishwasher out about 12 inches or more.
4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.
This was the second time I had this problem so I knew the symptoms and remedy. The tools needed were two nut drivers a ¼” and 5/16” along with a flat pry bar and Phillips screw driver. I started by removing the lower front panel by removing the two ¼” screws on either side. The lower panel will lift up and then can be removed by pulling on the bottom. There is a flat sheet metal piece behind the front panel with insulation that can be removed very easily along with the front panel. When the front panel is removed it exposes the front legs that may need to be dropped to let you lift the dishwasher over the tile (if you have ceramic tiles). The next step would be to remove any ties to the counter top if it is attached. Mine were attached by the two straps on either side with Phillips screws. After the top is free, lower the front legs by lifting the dishwasher with the flat pry bar and threading the legs up into their holders. With the legs lifted the dishwasher can be pulled out to expose the tension springs located along the sides at the very bottom. Chances are the ropes are broken off the plastic holders that fit over the door hooks. Remove the plastic guides by removing the 5/16” nut from the middle of the lower roller. Remember to note which hole the screw is coming from this also sets the tension for how fast or slowly the door drops. Placing the nut closer to the front will drop the door slowly and toward the back will drop the door more quickly. I placed mine in the middle hole. When the plastic guides are removed attach the nylon pope to the spring and attach to the back of the dishwasher. There is a hole located on a flat piece of sheet metal the spring will attach to at the back of the dishwasher (if it is broken). Check the other side if it is still in tact. With the spring in place weave the rope around the plastic guides then pull the springs to help get the plastic end over the door hook located at the bottom of the door. Repeat this operation for the other side (kit has a both sides covered) and reinstall dishwasher in cabinet. Steps 1) Remove front panel (1/4” nut) 2) Release Dishwasher from Cabinet 3) Lower front legs 4) Pull Dishwasher out from under Cabinet 5) Remove Rope Guide (5/16” nut) 6) Install new Rope Guide (Supplied in Kit) 7) Attach new rope to Spring and attach spring to dishwasher 8) Weave rope through rope guide 9) With door closed pull spring to relieve tension so rope can be attached to door 10) Repeat for other side (Kit has both sides)
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
Order within the next 0 mins and your part ships today!
Scott from Fort Lauderdale, FL
Difficulty Level:Easy
Total Repair Time:Less than 15 mins
Tools:Screw drivers
