WD-3245RHD (AMSEEUS) LG Washer - Instructions

The machine was making a grinding noise instead of draining. I spoke with the LG rep on the 800 line and was told to call a repair man. The Parts select diagram helped me to identify the part I needed. It was clear enough that I was confident it was the right one. Three days and six screws later the machine was working fine.

Found on line OE meant washer not pumping out water with the suggestion to clean the filter and inspect the pump and lines for blockage. No problems there. You must be careful to empty the water manually before removing the filter. My wet vac helped but I still made a mess. I found a mechanic to look at the washer. He said it is common for the pump on these washers to go bad, especially if the washer has sat out of service. They wanted $300 to replace the pump. I found the part on this website for $53 and replaced it myself. The only hard part was emptying the water without making a mess and leaning the washer up and back far enough safely to remove the pump, then working on my back under the machine.

1. Unplug washer. 2. Shut off water supply (hot and cold). 3.Remove hot water hose at washer inlet. 4. Remove the 2 plastic pieces that hold the washer top to the washer body by removing the 2 retaining screws. 5. Pull the top back to remove and set the washer top off to the side. 6. Unclip the electric harness from the inlet water valve. 7. With your pliers, loosen the clamp on the water inlet valve discharge hose and remove the hose from the valve. 8. Loosen and remove the 2 screws holding the inlet valve to the washer body. Install new hot water inlet valve and follow steps in reverse. Check for leaks before plugging washer back in. Run washer and check for leaks. Note: Excellent video available on You Tube. Consider replacing both the hot and cold water connecting hoses during the repair if they are old.

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

I watched a video of how to replace the pump and it showed taking the top and front off to get to it. I actually found this could be done by removing the back panel from the washer. There were two hose clamps you have to squeeze and slide up and two wires going to the pump. There are three screws holding the pump that need to be removed from the front of the washer. Once these are removed all you have to do is push a tab down and the motor slide right out. The pump assembly can also be reached from the bottom of the washer.

took out the drain pump and replace with a new one

During my troubleshooting, I removed the bottom to access the drain pump. I had to cut some wire ties so that I could make removing the wires easier. After checking the pump and putting everything back together, I determined that the pump itself was bad. Pump impeller should not rotate freely! After receiving new part, I installed it relatively easy. I didn't have to remove the bottom since there was enough room through the access hole. Just make sure to make where wires go before removing old part.

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

pulled off top of washer to get at the inlet valve disconnect two hoses take two screws out and then you put it back together the way you took apart and your done

Unplug Washing machine first. Then remove 2 screws at the back of the top cover. Slide the top cover back then lift and remove. Unplug electrical connector @ inlet valve and remove water lines 1 going in and 1 out of valve. Remove 2 screws holding assembly in place then install new valve assembly and all other components in reverse order.

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful

new pump was a little different ,but mounted properly. Tipped washer on its side, changed pump by working trough bottom and back access. It went pretty smoothly, works fine.

removed top, removed 2 screws, replace part. did not fix problem, the real problem was the water inlet valve, works great, easy fix. thanks

First we unplugged the machine. Then turned off the water and disconnected the hoses. Pulled out the machine and laid it on its side to access the themsistor located on the drum. (No, you do not have to remove the control panel at all to replace this part) The thermsistor is clearly seen with a flashlight. There were plastic ties holding the wires of the thermsistor so we used small scissors to cut the ties. Then unplugged the old thermsistor and plugged in the new thermsistor and used a regular bag twist to secure the wires. Repair complete and the machine is back to normal. Thank you Part Select.

Found great Youtube video, followed step by step. Only difficult part was getting the tub gasket clamp back on. But all in all pretty easy. If tub won't drain and weird noise coming from pump do not hesitate to do it yourself and save some coin!