Models
>
WCXH214A0WW
WCXH214A0WW General Electric Washer - Overview
Sections of the WCXH214A0WW
[Viewing 4 of 4]Keep searches simple, eg. "belt" or "pump".
Drain Hose
PartSelect #: PS417877
Manufacturer #: 131461200
This drain hose is designed for use in your washer. The function of this part is to carry water from the drain pump to the house drain. If your washer is leaking or will not drain, you may need to rep...
$20.58
In Stock
Washer Timer
PartSelect #: PS419227
Manufacturer #: 134014700
The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
$331.05
In Stock
CORD
PartSelect #: PS11766126
Manufacturer #: 5304505407
This is an authentic power cord, which works with washers and dryers.
$68.72
In Stock
Drive Belt
PartSelect #: PS269367
Manufacturer #: WH08X10003
This drive belt contains 6 ribs.
No Longer Available
Questions And Answers for WCXH214A0WW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WCXH214A0WW
[Viewing 4 of 4]Leaking
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Drain hose was leaking due to small hole in hose
This is the third time I have ordered parts from this company .I can't say enough good things about them from their fast shipping( always arrives sooner than they state)To the quality of the parts and the shipping packages.A first class operation from start to finnish.First step was to disconect power supply.Second was to remove washer dr
... Read more
ain hose from house drain.Third remove two (2) phillips head screws from front cover of washer ,located at bottom right and left side of front panel near floor.Lift front panel up to unhook metal retainers on panel that connect it to washer side panels.Use pliers to remove spring clamp from hose. Remove hose from washer pump. Remove clamp from hose,remove plastic retainer holding hose to washer bottom.Feed hose out the back of the washer through washer drain hose hole in the back pannel of the washer.Remove plastic retainer.Insert the new hose through the hole in the back pannel install the hose clamp and install the hose back on the pump.Relocate clamp on hose, take front panel,lift into place,push down to lock retaining taps into side cover slots replace the two phillips head screws.
Read less
Parts Used:
-
Carl from Wilmington, DE
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
31 of 34 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door catch broken
I paid a plumber $150 to replace this part a year ago. I simply took the screws out,ordered the part,paid for 1 day shipping, and screwed the new part on. The washer DID NOT WORK without this part,and worked perfectly the minute I replaced it.
Parts Used:
-
Jennifer from South Chatham, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
9 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
When you pulled the timer handle out to start the cycle, the water came on briefly then went off
Removed 6 screws off the rear of the control panel to expose the timer. Unhooked two wire clip connection from timer. Unscrewed the timer knob on the front of the control panel. Removed the plastic indicator sleeve below the handle. Removed 2 Phillips screws and the timer was out
Parts Used:
-
JEFF from SANDY, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!