WC484 Maytag Dishwasher - Instructions

I ordered two springs (PartSelect Number PS2202520), one for each side of my 30 year old Maytag WU704. This is the shorter "assist spring" that sits right behind the slightly longer green-ish spring, of which there are also one on each side. Now, with 2 springs on each side, the door swings like a new unit. I did NOT have to pull the dishwasher out of the cabinet at all. All I had to do was remove the base plate and there are gaps under the dishwasher frame that you can fish the spring with plastic grommet through, to insert the grommet into the appropriate hole on the door lever arm. Then with a pair of long needle-nose pliers I was able to reach from under the outside of the unit to grab the hanging spring hook and pull it down to insert it into the appropriate hole in the frame. I had a series, or line, of holes to choose from for this. I found that the hole closest to where the green-ish spring attaches made the door tighter and hold faster, the hole furthest made the door feel looser. You can do with one spring but I figure two would probably assist each other in lifting and last longer. Easy fix you can do! It would be an even easier fix if you need to replace the two other green-ish springs (PartSelect Number PS2097003), because they are right at the front of the unit. Open the bottom of the unit and check to see which is broken, so you are sure to order the correct spring(s) because they are different!

Seemed like I was getting more food stuck on my dishes than cleaned off. Because I've had this problem before, I already knew how to remove the lower spray arm and take off the large white housing beneath the spray arm with a special nut driver (shaped like a star) to get at the parts inside. The white plastic filter that circles the lower sprayer center was totally clogged and bent out of shape and was preventing the spray arm from turning. The microfilters built into the large white housing part that I removed using the special driver were also clogged from years of use. I cleaned the microfilters by agitation in water with lots of vinegar, poked the calcium deposits out of the holes that were clogged in the lower spray arm, and put the whole thing back together with the new plastic filter I bought from this site. Works like new again.

It was either the timer assembly of the Dispenser cup assembly. After looking at the dispenser critically< it appeared that the cam was quite worn. The replacement was accomplished by removing the bottom part of the door (4 screws) and then removing the dispenser cup (8 hex-head screws). If you keep the starter lever to "off" there is not power to the timer and you do not need to disconnect power

My daughter and son removed the old gasket and installed the new one. It went well.

Remove lower cover, 4 Phillips screws. Remove bracket with float switch, two hex head screws in the rear. After removal pull switch wires, two in plastic housings. Remove float switch, one small Phillips head screw. Remove float switch lever, one Phillips head screw. Clean the bracket and lever. Replace the lever and lube with silicone. Replace the float switch, (new one) and replace wires. Reinstall install bracket with original hex head screws. Replace lower cover. Done.

Removed four screws that hold front panel. Disconnected two wires, removed six screws, cleaned of old gasket material. Installed new gasket and soap dispenser with six screws. replaced two wires. replace front panel.

found the parts ordered them an poof dishwasher us as good as new

Looked into the problem, cleaned the sprayers out to no avail. Looked at drawings of dishwasher and noticed it had a filter. That seemed to be the next easiest thing to check. Removed the lower spray arm with channel locks, then removed the filter housing by removing 6 screw, removed old filter, replaced with new and reversed the above steps for re-assembly.

Piece of cake!

Removed lower spray arm and installed new seal under spray arm.Did not fix problem,I am guessing a low spray pressure.Everything checks out O.K.Anyone have some suggestions.How does the rinse aid get out of the holding tankr?

Called you on Saturday excellent operator placed order even with my card 1st refusing to do transaction. Received pump seal Monday (yes) and All the parts 3 days. Sears (only)the rubber seal! Used one nut driver, labor 1 hr. Thanks to everyone and the phone operator.. My wife is very pleased @ 3 days even over weekend delivery (and) price was less than sears. We shall shop your website again

Removed front panel by removing four screws. Used 5/16 nut driver to remove six screws holding dispenser and disconnected two wires. Inserted new dispenser and reattached cover. Longest time taken was to realign cover properly. Best approach seemed to install with door as near vertical as possible and to start screws by hand. ONLY FOUR screws hold the panel in place. Very easy repair for anyone. part arrived sooner than expected.

Shut off the hot water supply (pretty sharp eh?). Disconnected the hose from the hw supply and the at the connection to the washing machine. These had not been touched in at least 15 years and were somewhat tough to loosen but finally came ..... accessibility was a problem for the connection to the water supply as it was in a recessed wall box. Fortunately, we had some washers for the hose connections so the install was a snap. Hardest part of the whole job was moving the washing machine out from between the drier and the wash tub .... tight fit. Thanks for the quick service and to FED EX for their delivery. The delivery fellow was a real gentleman.

Followed instructions, those were OK.
Dishwasher front still leaking

Removed the seal and replaced with new one. Job went very easy. Stop the leake. Thank you.

Claude Miller

I removed four philips screws to remove the front door panel. Next I removed the screws holding in the detergent cup. Removed the two electrical wires from the cup release. Reveresed the process to install the new detergent cup.