WC482 Maytag Dishwasher - Instructions

had to remove the iner door plate and remove the main switch or latch to get to the micro switches witch one had over heated over time,it is working like new at this time.

Changed springs on both sides as long as I was at it. Did this without having to pull out built in washer. Lock the door closed to give the least tension on the springs. Remove kick plate at bottom of washer. Remove small access panels on each side. If you have small enough paws you can reach thru the access holes and strectch the spring with your fingers to remove and install new springs or use needle nose pliers if you have to. Don't forget the nylon bushings that come with the springs or the metal on metal contact will eventually nick the springs hook and make them break . Hook top end of spring first (rounded hook) and then stretch spring by grasping between thumb and index finger and hook into bottom hole. Hardest part is having to lay on your stomach to do it. Reassemble and count the money you've saved.

I removed the access panel and it was right there. one screw - disconect the wires & it was out. then right back in - access panel on, and done.

I removed the 4 lower Phillips head screws on the lower inside of the door.(thanks to a tip from Robert) This removed the front panel allowing access to the detergent cup. I removed the 6 screws holding the detergent cup. Removed the old detergent cup and gasket. Installed the new cup and gasket and reinstalled the front panel. Amazingly easy. Now it's on to my stove. I'm hooked on your website

I replaced a broken power cord in my 15+yr old portable maytag dishwasher as it was much less than a brand new one. I also need to change the seal in the door but that will be another day. Anyway, after removing the four screws inside the door with the torque screw driver (t20, I think) , remove the two screws attaching the counter top to the unit and took that off. You get to them from under the top when the door is open. Then remove two screws from the back of the unit. You can now remove the two screws holding the casing in the front of the unit. I think that is all you need to remove the casing and counter top. You now will need to remove a shield from the back of the unit. You will now need to remove four screws holding the front panel that hides the power cord box and other wires. The power cord runs into a small box that you will need to use the small socket to remove the cover. Disconnect the wire nuts and ground wire from the unit. This will release the power cord from the wires of the unit. Using a pair of pliers, pinch the black thing that holds the power cord in place and pull it through the hole it is slid into. You will need to use some force to do this. It took longer to do this than it did to get to that point for me. You must do this again on the side of the unit where the power cord goes through and runs to the back of the unit. Pull the old power cord out of the unit through the holes in the front and side where the black things were holding it tightly. You have removed the old power cord and are ready to install a new cord. Remember to run the power cord through the compartment in the back that it is to be pulled from when you operatate the unit. This is also where the hose comes out from. After running the cord through the back of the unit, through the side hole and into the hole in the front you have to re-install the black things that hold the cord tight. Be sure the cord is not touching the motor. I attached the cord to other wires underneath using duck tape keeping it away from the motor. This will require the pliers again and a little force to get the black thing to slip through the holes and keep the cord tight. It seemed easier for me to put the black thing in before I attached the power cord to the unit matching the colors up with the wires from the unit. This would be a good time to make sure the wires are connected by plugging in the cord and listening for the unit to start. I put the controls on the dry setting to hear the dryer start. After verifying the unit was connected properly, I used the screws that I took out to attach the box over the wires, attach the front panel, attach the rear shield, attach the casing, and counter top, or any other parts you may have taken off. The dishwasher is one!!!

Had to reuse the original mounting bracket instead of the one that came with the replacement part (held on by 4 screws). Also had to turn each solenoid 90 degrees (a feature of the replacement part) so that I could reuse the original connecting wires. Dishwasher running very quietly now.

"The order arrived in relatively short order. However, the installation must have been hilarious to any observer. Imagiine an arthritic septuagenerian getting down on the floor and wallowing about fitting a dish washer belt. Hints: 1. Grasp the pulley on the pump with your left hand from under the discharge hose (more room than over the hose) when fitting the belt to the rear of that pulley. 2. Use a hot pad (not an emroidered & quilted one reserved for company) to protect your L forearm from the frame member on the bottom of the machine. Getting up was worse than getting down, but it works! In dishwasher years it's much older than I am."

based on instructions from previous customers, took off front control and door panel, removed old gasket, replaced new gasket by aligning tabs and pulling through with needle nose pliers, leaking stopped

remove panel on front to acess float @ float switch.Remove phillips screw to float switch,remove palnut from float shaft with 5/16 nutdriver.Remove float from inside washer.Reinstall new parts reverse order.

Ordered a new Faucet Adapter! Simple

Found the adapter on Parts select through a google search. Unscrewed the existing faucet aerator and srewed in the adapter. The plastic shrink wrap holds the washer and screen in place, so don't open it until you're ready to install. Finger snug does it, only use the pliers to remover the old aerator from the faucet. Normally, I don't use pliers, but both of these parts were round and had vertical serrations to engare the plier teeth.

I bought the portable dishwasher on Craigslist, and it didn't have the connector that goes on the kitchen faucet. Ordered it here, got it in a few days, and didn't need any tools - just had to screw it on. Good as gold!

I knew I needed a faucet adapter, but thought I could just go to my local home depot and get the part...not so much. After 3 trips and not getting the part I truly needed I ordered the part from partselect. I received it literally the day after I ordered it, screwed in place with no tools, attached the coupler/hoses to the faucet and washed dishes. I wish I would have ordered the part from partselect before even bother with home depot. I would have saved myself a lot of trouble! Extremely happy! Thank you!

Replaced the faucet adapter, works fine

I unsrew the faucet head, and attached th e adapter