WC482 Maytag Dishwasher - Instructions

Very simple. Remove bottom panels. Remove one screw holding old switch in place. Move wire connections from old switch to new one. Cleaned and lubed the switch actuator. Mounted new switch. Checked that float and actuator worked freely. Left bottom panels off till I ran a load - just to be sure all was OK. Remount bottom panels...Done! P.S. Don't forget to turn power off to dishwasher any time you work on it!!

Since the bimetal repair kit was not available, I bought the complete detergent cup, gasket, and bimetal switch assembly set. This was still far cheaper than paying for a professional repair. All I had to do after shutting off the power is to remove screws to open up the door (door trim/6 screws & 6 screws on the inner side of door edges to remove outer wall of door). The detergent cup assembly is right there for easy access! I unplugged the 2 electric wire plugs to the bimetal switch (paying attention to which plug goes where for when I reassemble), removed the 6 screws that mount the cup assembly, removed assembly and gasket, cleaned the surfaces, and reassembled with the new assembly. Very, very easy to do and everything works like a charm!

this is a portable unit
the wood top is removed this allows access to the side cabinet screws and the lower front trim screws behind the lower front trim panel you can access the hose connections disconnect and reinstall
new part works great!

I was not able to follow the instructions exactly since they called for stretching the belt around the back pulley with the left hand. For a woman that prooved too difficult so instead I attached the belt to the back pulley first and used 2 screw drivers (they are thin) to stretch the belt around the front pulley. It took considerable effort but I got it on!! The dishwasher now works. Praise God!!

Just as everybody explained, 4 screws for the door panel, 6 screws for the dispenser, out and in, 15 minutes!!! There are plenty of screws on the door but, once i knew i was looking for 4 screws, it was a cinch!!! Thanks for that tip. All my appliances are the same age so i 'll be back to this site again!!

followed the scematic on the wesbite that i used to i.d. the repair part needed. removed the front door outside cover (8 screws) removed the bi-metal switch (2 screws), did not need to replace the door latch or spring. replaced the switch and the front door cover and ran the dishwasher to test the new switch. worked fine and has been working fine.

Removed two panels on front bottom to gain access to motor and pump pulley.
Looped belt around motor pulley and partially looped belt on larger pump pulley then turned pump pulley together with the belt until belt was fully installed., then coated belt with silicone grease to lubricate it.. very simple procedure.

One note of precaution, UNPLUG power plug before working on appliance.

first I removed the 4 screws that hold the bottom part of the door cover and then removed the 6 bolts
with a power screw driver with nut attachment.I then reomved the 2 wires which are color coded and noted which one went where.I removed the old unit and installed the gasget and new detergengent cup,the wires,bolts and door screws.You do not have to remove the screws to the top part of the door.The screws are located inside the door on each side. Took about 20 minutes.

It was my first dishwasher belt and it was much tighter than I thought it was going to be. I was worried I was going to break it putting it on so I was a bit stumped, but finally got it on and its good as new.

1. Removed the four screws to remove the door front.
2. Removed the six screws to remove the detergent cup.
3. Replaced bimetal strip, cam, and spring. (simple task)
4. Replaced gasket and seal.
5. Replaced detergent cup.
6. Replaced door front.

Very easy,take off the old faucet screen and screw on the adapter. What I really liked was the ease of ordering the part. In less than 5 minutes I had located the part and ordered it. Less than 3 days later, I had the part. Way to go PartSelect.

I removed front bottom cover,found belt broken. I ordered part online on 10-23-09,part arrived on 10-24-09,amazing. I lossened the two bolts that hold the drive motor to the frame,slipped the new belt on and applied the supplied silicone grease. I then ran the two bolts in with a 3/8 wrench,put the cover back on. Everything works like new now. Great delivery and easy ordering system online. Immediatly called my neighbor and told him about partselect.com

First, I had to remove the outer face panel of the door. Four screws on the inside of the door hold the large panel onto the front. Removing these screws and the panel revealed the detergent cup assembly. There is no need to disconnect the power as long as the door latch is in the open position for this repair. I removed the two wires, blue and white from the leads, keeping note which was attached to which lead. I used a hex head screw driver to remove the 6 screws that hold the detergent cup in place. After removing the detergent cup and gasket, I cleaned the surfaces with a scouring pad to make sure the new gasket would have a good seal. I installed the new detergent cup with the 6 hex screws and re-attached the leads. I replaced the face panel with the four interior screws after running a couple cycles to be sure the problem was fixed, which it was.

Had to loosen the drive motor enough to slip the belt around the pulleys. The only problem was the amount of space available to work in.

I replaced the belt and door spring. Now it works perfectly, and the door doesn't drop with a bang.