W25HA2 Magic Chef Washer - Instructions

I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.

diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.

Remove tub assembly per snubber replacement procedure.
Place tub assembly on top of a milk crate open-side up.
Support tub assembly on milk crate with 2x4's to protect pully from damage.
Remove agitator from tub assembly.
Press down on tub assembly cap, release tabs and remove tub assembly cap.
Remove inner tub from tub assembly.
Mark tub frame with location of outer tub air bell for ease of reassembly.
Remove outer tub from transmission assembly.
Replace inner tub gasket
Replace outer tub gasket

Problem encountered was that the replacement tub had a defective air bell. The washer consequently did not detect fill level and subsequently overflowed flooding the laundry room. The bell looked ok visually. Blowing into the air tube while plugging the inside hole with a finger revealed a pinhole leak in one corner of the PP weld. PartSelect was prompt with replacement, but the job had to be redone in its entirety.

Always test the air bell before installing an outer tub.

Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.

Removed back access cover and lift top cover looking for leak. Initially thought it may have been the pump housing. I filled some water into the tub and I flexed the hose between the tub and the pump and water sprayed out. It had cracked in about 3 small places (water is present in the hose anytime water is in the tub) Ordered and replaced hose. Also order drive belt and replaced as a preventive maintenance item.

Remove the metal plate in back of the washer that 3 screws. I use a vise-grips to remove the two clamps.One on other the tub side and the other the pump side. Pull the old hose off the tub side and the pump side.Use the old clamps to put the new hose on.

I pulled the top ofthe washer up, I disconnected the cold and hot water hoses, took the 2 bolts off with a socket and pulled the water valve from the top. I used the pliers to take the pressure ring off and pulled over flow hose off. I pulled the four wires off with pliers. Put the new water valve in reverse order...easy.

I ordered the replacement pump assembly (water pump)for my Atlantis model maytag washer, removed the old one, installed the new one and works like a charm. The only difficulty I had was trying to figure out how to remove the cover on the front of the washer, to remove the clips, it slid side to side instead of popping out, found the instructions on-line, NO instructions came with the pump but if you have any common sense when it comes to repairs it was easy to remove and install the new part.

Spoke with a trusted repair man, described the problem best as I could. I smelled a burning rubber smell. Got on Internet for troubleshooting problems, 77% likely a drive belt. BINGO! Ordered a new belt, took old one off, cleaned the pulley ( it had burnt rubber stuck on it, difficult to remove) lightly sanded pulley just so it would be really smooth. replaced belt. Magic, it worked. I am no repair woman, but carefully listening and explaining helped. Oh, belt is under the very bottom of machine. Very easy to get to, just tilt back and lodge at an angle and make sure it doesn't move.

took off back small metal panel, tilted washer front side down, easy to put into place after removing old part

I placed the washer on a couple of work-horses so I could have access to the belt underneath. Then I used my nutdriver to removed the lower back panel. Disconnected both of the hoses, and removed the pump with my nutdrivers. Placed the new pump in place, placed the belt back on the pump's pully, tightened down the pump. I then plugged in the washer and put a little water in the washer to test that everything was working. After confirming that everything worked, I replaced the lower back panel and put the washer back in business. 30 minutes from beginning to end ... and a good time was had by all.

1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy out,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!

took drum out replase snubber put drum back in

Turned it over to my 35-year old son who removed pump and pulley assembly and the old drive belt, then simply replaced with new assembly and belt from PartSelect! Could not have been easier - from my viewpoint.

Raised washer. Identified problem. Removed from panel, gaining access to drain pump. Removed hoses, replaced pump. NOTE: I used blue Loctite on pump mounting bolts. Reinstalled from panel, lowered washer, cleaned drum. Ran one (1) cycle with hot water and bleach ONLY.