W20HA5 Magic Chef Washer - Instructions

I followed Gary from Sioux City IA instructions. Very well explained.

Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and did a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.

I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise!

diagnosed a loose belt-- ordered and received same -- installed and set to proper tension that was simple.

I tilted the machine on it's back to remove the drive belt. You could feel the friction in the pump when you turned the pulley. I set the machine back down and removed the back cover (4 screws). I removed the two hoses with a pair of pliers. I used a small socket set to remove the three mounting screws. I ordered the pump. I reversed the process to put it back together. It took about 35 minutes to determine what the problem was and to remove the pump. It took about 20 minutes to put it back together.

Removed front of washer following instructions on partselect.com (used putty knife to release catches). Removed hoses and belt from pump, then removed and replaced the pump. Reattaching the belt was the only awkward task.

I placed the washer on a couple of work-horses so I could have access to the belt underneath. Then I used my nutdriver to removed the lower back panel. Disconnected both of the hoses, and removed the pump with my nutdrivers. Placed the new pump in place, placed the belt back on the pump's pully, tightened down the pump. I then plugged in the washer and put a little water in the washer to test that everything was working. After confirming that everything worked, I replaced the lower back panel and put the washer back in business. 30 minutes from beginning to end ... and a good time was had by all.

I diagnosed the bearing by putting a 3/4 inch rubber hose up to my ear. I pointed it around until isolating the noise to the pump. The bearing was not servicable without replacing the pump. After diagnosing the problem I ordered the part. Getting the part from PartSelect.com was a snap. It arrived in one day. In 15 minutes I had it back to gether and working quiet and smooth.

I pulled the top ofthe washer up, I disconnected the cold and hot water hoses, took the 2 bolts off with a socket and pulled the water valve from the top. I used the pliers to take the pressure ring off and pulled over flow hose off. I pulled the four wires off with pliers. Put the new water valve in reverse order...easy.

tilted the machine forward, worked off the old belt and put the new belt back on. no tools required, done in less than 5 minutes.

All i had to do was pull the washer machine from the wall and lean it back as far as i could and get under it and place the (DRIVE BELT) on the two smallest pulley then put the belt on the large pulley and my work was done it was very simple and easy.......

Leaned the washer back and propped it up and changed the belt. This is the first time ever repairing an appliance. I feel very good about myself as I am 49 yrs old and did not have to call a repairman for this.

I pulled the washer away from the wall so that I could lean it back at an angle. I removed the old belt and put the new one on. I started with the smaller pulley first and put the belt into the groove. Next I went to the next larger pulley and did the same thing. Then I went to the largest pulley and started to put the belt into the groove and started turning the pulley by hand. The belt went right on.

pulled out the washing machine that was the hard part, tilted it back checked too make sure everything spun by hand just to see if that was reason for the belt to snap but everything spun by hand nice and smoothly poped on the drive belt and everything works fine back in business.

First I am a woman and was able to do it, and if I can do it anyone should be able to do this. The service call alone was 75.00, and the belt was 23.00 with shipping. First we tilted the washer at a 45 degree angle and I removed the belt, and just rolled the newer one on the track. That was it and I was done. My washer now purrs like a kitten love it. And Part Select sent out my part and I recieved it next day, thank you for wonderful service that kind of service is hard to find. <3