W20HA23 Magic Chef Washer - Instructions

I placed the washer on a couple of work-horses so I could have access to the belt underneath. Then I used my nutdriver to removed the lower back panel. Disconnected both of the hoses, and removed the pump with my nutdrivers. Placed the new pump in place, placed the belt back on the pump's pully, tightened down the pump. I then plugged in the washer and put a little water in the washer to test that everything was working. After confirming that everything worked, I replaced the lower back panel and put the washer back in business. 30 minutes from beginning to end ... and a good time was had by all.

I first opoen the front panel of the washer. That was a bit tricky. Had to slide a thin blade between the top of the washer and the front panel, pushed in to release the "clamp" and gently raise the top, it hinges on the back.
The rest was undoing three bolts, refit the new pump and put the belt back on.
The part cost me less then $65.00.
The repair estimate by the local repair man was $ 250.00.
I am very happy.

Thank you PartSelect.

Andre M. Roberty

Spoke with a trusted repair man, described the problem best as I could. I smelled a burning rubber smell. Got on Internet for troubleshooting problems, 77% likely a drive belt. BINGO! Ordered a new belt, took old one off, cleaned the pulley ( it had burnt rubber stuck on it, difficult to remove) lightly sanded pulley just so it would be really smooth. replaced belt. Magic, it worked. I am no repair woman, but carefully listening and explaining helped. Oh, belt is under the very bottom of machine. Very easy to get to, just tilt back and lodge at an angle and make sure it doesn't move.

Removed back plate, tilted up washer removed pump removed belt. Then replace pump and then replaced belt

Unplugged everything, disconnected hoses, took belt off and put new one on.

Unbolt old pump with three bolt from top of pump inside the washer. Use needlenose pliers to remove intake and output hoses from old pump. Remove belt from pulley under washer. Reverse procedure to install. I was worried because there were two pumps listed for this model number, one being $95 and the other being $40. I bought the cheaper one and prayed. It worked just fine. Fixed a $500 washer that was on it's way to the dump and made $100 in the process!

tilted the machine forward, worked off the old belt and put the new belt back on. no tools required, done in less than 5 minutes.

All i had to do was pull the washer machine from the wall and lean it back as far as i could and get under it and place the (DRIVE BELT) on the two smallest pulley then put the belt on the large pulley and my work was done it was very simple and easy.......

Leaned the washer back and propped it up and changed the belt. This is the first time ever repairing an appliance. I feel very good about myself as I am 49 yrs old and did not have to call a repairman for this.

I pulled the washer away from the wall so that I could lean it back at an angle. I removed the old belt and put the new one on. I started with the smaller pulley first and put the belt into the groove. Next I went to the next larger pulley and did the same thing. Then I went to the largest pulley and started to put the belt into the groove and started turning the pulley by hand. The belt went right on.

pulled out the washing machine that was the hard part, tilted it back checked too make sure everything spun by hand just to see if that was reason for the belt to snap but everything spun by hand nice and smoothly poped on the drive belt and everything works fine back in business.

First I am a woman and was able to do it, and if I can do it anyone should be able to do this. The service call alone was 75.00, and the belt was 23.00 with shipping. First we tilted the washer at a 45 degree angle and I removed the belt, and just rolled the newer one on the track. That was it and I was done. My washer now purrs like a kitten love it. And Part Select sent out my part and I recieved it next day, thank you for wonderful service that kind of service is hard to find. <3

took drum out replase snubber put drum back in

1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy out,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!

Turned it over to my 35-year old son who removed pump and pulley assembly and the old drive belt, then simply replaced with new assembly and belt from PartSelect! Could not have been easier - from my viewpoint.