Models > TGF364ASB > Instructions

TGF364ASB Tappan Range - Instructions

All Instructions for the TGF364ASB
91 - 105 of 367
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
guide was broken
Used a slot screwdriver to pry the old guide...clipped the new guide into its place.
Parts Used:
Front Drawer Glide
  • Marvin from MONTANA CITY, MT
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad ignitor
This was very easy. Just remove the bottom of the oven by removing the two screw in the back. Then remove the baffle from under that and you of will see the ingniter. The one wire will reach the gas valve, just splce the other. 6 screws is all it takes. Turned it on worked perfectly.
Parts Used:
Flat Style Oven Igniter
  • James from ULSTER, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not light up
Remove oven racks and bottom oven panel cover.Removed old igniter.one screw was stripped so that slowed me down quite a bit! Used a small vise grip tool to remove screw! installed new ignighter,cut existing wires; spliced in new wires( be sure to unplug appliance) tested ok. Reassembled.
Parts Used:
Flat Style Oven Igniter
  • John from St.Albans Bay, VT
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wasn't staying on and or re-lighting, recycling to maintain the set Temp.
Opened the oven door, removed the racks. Removed the bottom cover, two thumb screws in the rear, bottom, of the oven. This exposed the top plate of the burner, (actually in the top of the broiler section) 1 nut took this cover off. Now, the burner and the igniter are exposed. Two screws removed the igniter, and two wires with ceramic wire nuts. Disconnected these two wires and that was it. Installed the new igniter in reverse procedure as above. Pretty easy. Probably should have turned off the power to the Range first just to be safe.
Parts Used:
Flat Style Oven Igniter
  • michael from MILFORD, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven very slow in lighting, then when got to correct temp shut down but wouldn't relight
1- put in new thermostat 2- put in new gas valve 3- put in oven igniter ....3rd time a charm. Now I have all new oven parts! My husband installed and said it was pretty easy, have to take the oven door off and inside bottom out.
Parts Used:
Flat Style Oven Igniter
  • Marlene from SUTTON, NE
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
oven wouldn't light uneven temp.
had to remove burner bolts holding igniter were stripped cut two wires replaced igniter using two self tapping screws put wires together using wirenuts Honey making cookies right now thanks already told friends about you
Parts Used:
Flat Style Oven Igniter
  • Paul from Akron, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't light
Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?
Parts Used:
Flat Style Oven Igniter
  • JERRY L from PIPER CITY, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
One guide was missing and the other was broken
Read the instructions provided and simply installed the guides. Total time was less than 5 min.
Parts Used:
Front Drawer Glide
  • Don from WEST UNION, OH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
GAS OVEN WON'T LIGHT.
AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.
Parts Used:
Flat Style Oven Igniter
  • stephen from LIVERPOOL, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed an additional rack
Open the door and slide in the new rack.
Parts Used:
Oven Rack
  • Gary from Darragh, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
OVEN WOULD NOT COME ON
CUT THE WIRES ON OLD IGNITER AND WIRE NUT THE WIRES OF THE NEW IGNITER TO WHERE I CUT THE OLD ONE OFF.
Parts Used:
Flat Style Oven Igniter
  • david from SLIDELL, LA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced theoriginal power cord.
moved the stove forward and removed old cord by uncruing two small screw and on ploged the all and replaced with the new one.
Parts Used:
CORD
  • Blanca from Union City, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not light
Removed old control installed new part oven worked ok
Parts Used:
Electronic Clock Control
  • Richard from ELIDA, NM
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Never received parts from PartSelect!!!
It went easy, I ordered the part from another vendor, received it in 3 days and it only took about 20 minutes to install.
I do not recommend ordering from PartSelect!
Parts Used:
PROBE
  • Ralph from SULLIGENT, AL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
over draw was off track
the part snapped on the side of the track, now the draw is not sitting on the floor and opens and closes like new.
Parts Used:
Front Drawer Glide
  • Frances from Hauppauge, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the TGF364ASB
91 - 105 of 367
Back to Top