Quick Question!

Have you ever purchased from PartSelect.com before?

Models > TGF362BBBA > Instructions

TGF362BBBA Tappan Range - Instructions

All installation instructions for TGF362BBBA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the TGF362BBBA
226-240 of 377
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broked drawer slide

  • Customer: Thomas from Spring Hill, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
The plastic drawer slide that the lower stove door sits on broke. (one on each side) Remove the old one with a screwdriver and snap in the new one, took 1 minute because I replaced both of them.
Excellent fast delivery. 5 stars !

lower drawer drags on floor

  • Customer: columbus from birmingham, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
remove/pry broken plastic glide from in-side of oven,( wall not drawer ) and install new one.

Oven Pilot Heater Would Glow, Burner Would Not Light, Smell Of Lp Gas

  • Customer: JOHN from SOPCHOPPY, FL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 2 people found this instruction helpful
After reading the input of others on your site I ordered the igniter. Within a short time it was installed and the oven works fine. Thanks for the help, jc

Actually, the igniter I purchased is to be used on my furnace.

  • Customer: Lester from Waynesville, MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 1 of 5 people found this instruction helpful
I have a Nordine model G2RC-105C19 LPG gas furnace. It was installed in 1995. The igniter went out and my son who was a propane gas appliance service tech installed one that was for our gas range. He said they were the same with the exception of a metal mounting plate on the stove igniter. Once the plate was removed, the igniter fit perfectly on the furnace. As a side note, the one I just bought from PartSelect was less expensive than one for the furnace.

Broken drawer glide

  • Customer: Pamela from Presho, SD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
Glide just slipped out and the other in.So pleased at how fast the part arrived!! Less than a week.

Oven would not ignite because the ceramic was cracked off

  • Customer: Michael from Spring Grove, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 0 of 3 people found this instruction helpful
First i disconected the plug went right where the trouble was.removed the two screws and the safe plate that is protecting the wires.disconeted the two wires and replaced the new ignighter. put everythin back together tried it out ond guess what ??? it works .. Thank you

The front drawer clip was broken

  • Customer: Clarence from Colorado Springs, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took the drawer completely out and installed the new clip just like the video instructed. All went very well with no problems. The drawer works like new. I am glad that I was able to find the part on this site. Thank you so much. I will be using this site in the future.

Igniter electrode broke

  • Customer: Robert from Weidman, MI
  • Difficulty: Really Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
The three bolts that held the burner busted off when tring to loosen. I drilled out the old studs and replaced with self tapping screws.

Didn't have back slides

  • Customer: Susan from Diamond, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very easy. Dont know why I didn't do this earlier.

Broken Front Drawer Glide

  • Customer: Larry from Dunedin, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Snapped in the new replacement part and intalled stove drawer in less then two minutes.

The drawer on the bottom of the stove would not close properly. When I opened it, it would fall on the floor.None of the parts stores around here knew what I was talking about and couldn't supply any parts.

  • Customer: Jewell from Port Charlotte, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I searched the internet for help, that lead me to your site. I typed in the make and model. Within seconds some drawings appeared, showing the part I needed. I watched your video on making the repair. You make it so easy. I ordered the parts you recommended. They arrived in just a couple of days. I went back to your site to take another look at your video and I was ready. In just minutes, I had the drawer out, installed the new guides. The one side, the guide was completely gone, so I could snap in the new2 guide as you recommended. The other side, the guide was broken off and I had to use a needle nose pliers to get it out. Then snaped in the new guide. Re-installed the drawer with all the goodies, wax paper, tin-foil, baggies etc. Closaed t6he drawer and everything lined up perfectly. Thanks to you I've got a drawer that works again aqnd I got it done before my husband got home from work. Funny thing, he hasn't complained or asked me about the drawer. I guess that will be our little secret....Thanks Julie

While cleaning the oven of some excess burned on food, I inadvertently broke the inside glass in the door

  • Customer: Nancy from Hendersonville, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed door from unit (easy) and separated the inside of the door from the outside and replaced the broken glass with the new replaceable glass. Took the time to also clean in between the two glasses. Looks great!

Range drawer wouldn't close properly

  • Customer: Kenneth from Vancouver, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed the drawer, simply snapped the rear drawer glide in the punch-out by hand, replaced the drawer. Works well

rear drawer glide broke

  • Customer: Barbara from Concord, CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The repair was as simple as reattaching the broken glider. No tools were needed.

Stove not lighting and taking forever to preheat

  • Customer: Julie from Huffman, TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My mom did the repair for me. We did not have the right tools for the job which made it harder to do. First I flipped the breaker. Then we took out the oven racks. We then took the bottom metal part off the oven. This exposed the shield part and we removed it. Then she cut the wires and connected the new igniter the same way the old one was connected. It took about thirty minutes. We could do it again in about fifteen with the right tools. We went and priced new stoves the cheapest was 350.00. I'm so excited that my stove is working properly again.
All Instructions for the TGF362BBBA
226-240 of 377