TG518SL (P1180901W) Amana Refrigerator - Instructions

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

I removed the screws holding the old, cracked handle in place, and used the same screws to affix the new handle, which fit perfectly. The whole job, including a bit of cleaning to remove the scuzz that had built up around the top and bottom of the handle over 13 years' time, took about 5 minutes. Note: the screw at the bottom is covered by a small plastic tab (easily removed by prying, gently, with a screwdriver), which doesn't come with the new handle, so if covering the screw matters to you, don't break or lose the old one!

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

I opted not to remove the entire door which did not cause any problems, and did not add to the complexity of the job by adding another step. I simply removed the numerous bolts from the sides an bottom of the existing gasket and loosened, but left in place, the top row of bolts. I slipped the old gasket out and slipped the new gasket in. Then tightened one bolt per side to secure it in place and verify it was even around the perimeter, then tightened all remaining bolts and then wait for the applause.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

very easy.....
1. removed the food items from the shelf
2. raised the shelf and removed the broken support post
3. inserted the new support post and guided the drawer rails to rest in the new support slots
4. cleaned the glass shelf and replaced the food items
5. made my wife very happy now that the veg drawer opens and closed like new.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

I first removed the screws from the upper 2/3 of door gasket and remove that portion of gasket. Put new gasket in place and re-installed the screws on the top section. Removed the rest of the screws, completed placement of new gasket and re-installed all screws. It is not necessary to remove the door. Piece of cake repair.

The part was delivered in just a few days. We merely had to unscrew the broken handle and screw in the new one. The color matched wonderfully and funcitoned beautifully.

Pop loose the plastic grate at the bottom.

Locate and remove the wheel leveling screw from the front bottom corner.

Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.

Lift out the wheel assembly.

Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.

Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.

Reinstall and adjust wheel assembly.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

The good news is that the part (the wheel was available.) I bought two in the event that the other wheel may break in the future. The bad news is that the housing that holds the wheel was riveted together by the wheel axle. It would have been nice to know that before I bought the part and if the housing with the wheel installed was available. The refrigerator was at my summer house a hundred miles away. Anyway, we had to grind the end of the riveted axle to dislodge it from the wheel housing. With the axle dislodged from the housing we were able to install the wheel and then hammer the end of the axle flat to keep in place, like the original rivet installation. It is not perfect but it held and should be fine. I am glad I was able to get the part and will be back in the future, if in need of other parts.

I hired a jack-of-all-trades friend of mine to do the job. He had just the right tool to take out all the screws so that went smoothly. Slipping the new gasket into place while I held the inner door shelving section in place was a little tricky and the gasket seemed a little off along the bottom and one side of the door frame. We gave it a couple of days to seat itself. Two days later, there was condensation forming inside so my friend returned and took a look. He spotted a couple of places where the gasket magnet was not sealing properly. Out from his pocket, he pulled what looked like a brass jack knife with japanese writing on it and said it was a japanese carving tool. He opened up one of the parts that had a smooth blunt tip on it and slid it down the channel in the gasket from the outside. Voila! The magnet grabbed. He adjusted a couple of screws along the bottom and , after that, there were no more problems. So be sure to have your japanese carving toll ready when you start this job!

I removed the 3 screws that held the handle on refrigerator, then cleaned up the grime before putting on the new handle, which fit perfectly. The only complaint I have was there were no new screws with the handle. I am a single woman and this was a very easy project for me. I am very satisfied with the product, and with the fast delivery.