TFS22PPBCBS General Electric Refrigerator - Instructions

removed old auger; replaced it with a stainless steel auger

First, I removed all items on the door shelves and the shelves themselves to reduce the weight of the door. The door came off by itself because the bottom hinge had broken. Then I placed the door horizontal on the kitchen floor to have easier access to the bottom of the door. I had a piece of blanket under the door to prevent any scratch. I then removed two screws holding the door closing cam and shim and replaced them with the new parts. Next, I removed the base grill to have easy access to the old hinge assembly on the refrigerator itself. All I had to do was grab it firmly at either end and pull it forward. I replaced the hinge assembly with the new one. I removed the cover on the top hinge assembly and removed the two screws that secured that hinge (I was not able to put the door back without removing the top hinge assembly). All down hill from this point. Time to reinstall the door, aligning the bottom of the door cam over the hinge assembly and setting the door down on it making sure the door sets on the hinge assembly cams. To the top of the refrigerator. reinstalled the top door hinge assembly and cover (I had to make sure the door was standing straight vertically before I tightened the nuts), I also put a small amount of white grease into both the top and bottom hinges.

Propped the door up with wood so we could change it without removing the whole door.
Removed &Replaced the cam and bracket quite easily. It did require 2 people, one to help hold the door while the other did the work.

Removed the screws holding the faceplate. Then couldn't change out the auger so needed to remove all of the other screws in the unit and fully disassemble the icemaker unit. Should have marked the parts as I took them apart as I needed to find a parts diagram on-line to reassemble. Not sure that I put them back together right as the unit will not dispense whole ice cubes as it did previously.

The icemaker arm disconnected from the metal frame. This caused the icemaker to cycle and the heater to come on and stay on until the plastic parts melted causing a mess and stink. This action melted the ice and then the water fell through the frozen items in the freezer and refreezed in the lower portion. OK, I remover the dead icemaker and tossed it away. I installed the new icemaker and the wiring harness didn't fit right (way to long). I retrieved the old icemaker and removed the wiring harness from it. I removerd the new ice maker and installed the old wiring harness to the new icemaker. I then installed the new icemaker, plugged it in and turned on the power. No water, I ordered the dual solenoid water valve, installed it with difficulty (another story) the turned on the power. I reinstalled the ice bin and found it didn't fit. The icemaker was to low and couldn't be adjusted, 1/4" higher would have been great. I shoved in the bin anyway, I was out of ice for my scotch, and it started making ice.

instalation was very easy - but the part was 3/4 inch to long and a 1/32 inch to wide.Trimmed it with the "faithfull"
Dremel and it works!The instalation part of the "job" was less then 10 min.

Replaced icemaker assembly. Only 3 Phillips screws to remove the old assembly. Pretty much an exact swap. Was easy to replace but the connecting cable on the new replacement assembly wasn't very easy to make fit. Had to force it into a location that would be out of the way and allow everything to operate properly. That connecting cable should be more flexible and adapt to the fridge a little more friendly.

I simply removed the screws holding the plastic face plate to the old auger/ice bucket and attached it to the new one. It was a simple procedure

The replacement part fit perfectly and was easy to install. No problems at all.

put block of wood under the door, removed old hinge and installed the new one. about 15 minutes

replaced lights in refrigirator and freezer

Removed the door by removing the top hinge and lifting it off the broken bottom hinge/cam assembly. Removed the broken hinge/cam assembly found out why the cam broke the doorstop was bent so I had to order the doorstop also. The ordering of the parts was so easy. They shipped them on Monday and they arrived the next day. I will use Parts Select again

removed the back of the freezer unit and replaced the defrost heater and thermastat. took the controls out of the produce side and replaced the defrost timer.

Removed everything from the refrigerator door. Removed the screw holding the cover over the top hinge. Removed the two (8mm) bolts holding the top hinge to the refrigator. Removed the door. Removed the plastic grill/cover and the two (8mm) bolts from the lower hinge assembly. Installed the new hinge assembly. Replaced the closing cam (included in the hinge assembly kit) on the bottom of the door. Put the door back on the lower hinge. Installed the upper hinge. Adjusted the door and tightened the bolts on the upper hinge, and replaced the hinge cover. Done!

First removed the two screws that holds the old ice maker in place. Unplugged it. The freezer compartment was too narrow to allow the unit to slide out or turn in any other direction. Had to also remove the two front screws from the left side ice bin track and swing it down. The door opening was also too tight. Scratched the plastic door jamb putting the new unit in but other than that all is well and functioning well.