All Installation Instructions for Whirlpool Range TER46W0WN1

Broiler wouldn't heat

First I removed the ovem door, then I removed the 4 screws, unplugged element and plugged in the new one, then replace the screws and door. It should have been a 10 min job but I'm old and a bit fat...slowed me down.

Parts Used:

Broil Element - 240V

Diane from Mill Valley, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

7 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Inside glass window pane on oven door cracked.

First tried to replace the glass and gasket without removing the oven door. Removed all screws and took the door apart. However, I found it was very hard to get the gasket to stay in place and put the glass window in place with the door frame still attached to the oven and upright. Decided to go ahead and lift the door off the hinges by removing the two final screws. Then the door could be layed flat on the floor and it was much easier to put in the insulation and glass pane.

Parts Used:

Range Inner Door Glass

Glass Door Gasket

Susan from San Jose, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

7 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Broil Element Was Burned Out

1. Move oven out from wall 2. Remove back panel of oven, 8 screws 3. Remove 3 screws inside oven holding element 4. Pulled wire connections off of element 5. Reverse procedure to install new element

Parts Used:

Broil Element - 240V

DAVID from COTTAGE GROVE, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

9 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Oven would not reach selected temperature

First, shut off the power at the breaker panel. Next, I simply unscrewed the screws holding in each element, disconnected the leads, reconnected the leads to the new elements, positioned each element & reinserted the screws. A suggestion: Before loosening the screws, a light shot of PB Blaster or similar might help.

Parts Used:

Broil Element - 240V

Oven Bake Element 2600w 240v

Howard from BRYAN, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Oven bake element

Open oven door. Still power to the wall, but all Knobs in "OFF" position. two phillips screws, pull old element back, and disconnect both leads. Put the leads on the new element and reinsert with two mounting screws. Simple.

Parts Used:

Oven Bake Element 2600w 240v

ross from DEARY, ID
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Element wasn't being controlled by the switch it would stay on high

Ordered a new switch and replaced the old one with it.

Parts Used:

Surface Burner Element Switch, Large Burner

George from FRANKLIN, KY
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 7 people found this instruction helpful.

Was this instruction helpful to you?

The upper broiler element had burnt and broken into.

I must compliment PartSelect on their quick responce and delivery of the item ordered. It arrived a day after I had ordered it. Trust me, the $40.00 I spent on the item was way cheaper than having a repair service fix it or having the entire oven replaced. I would highly recomend anyone to utilize PartSelect.

Parts Used:

Broil Element - 240V

William from Manteno, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Wrench (Adjustable)

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Oven wouldn't heat

Ordered element and received it the next day. Removed two screws that holds element in place. I then pulled the element out about 3 or 4 inches and disconnected the two wires. Put new element in connected the wires mounted element in place with the two screws. Now works great!

Parts Used:

Oven Bake Element 2600w 240v

Michael from Wichita, KS
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

The burner would not shut off.

Pulled the dial off, unscrew two screws. Pull the switch out from the back. Disconnect the wires from the old switch and connect to the new switch one by one. Set the new switch in place. Sctew the two screws in to hold the switch in place. Push on the dial.

Parts Used:

Infinite Switch - 6 Inch

Richard from CONCORD, NH
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

The Bottom Element Was Not Heating

Unplug first then took back off and took wire clips off and connectected the other on in worked fine you will like part select I just ordered apart for my frig. Waiting for it now.

Parts Used:

Oven Bake Element 2600w 240v

y.d. from lagrange, KY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

electric burner burned out

This is the second time PartSelect came through for me. If it hadn't been for you guys, I'd have had to buy a new Jenn-Air cooktop, because ours is nearly 30 years old. About two years ago, I bought a new two-burner cartridge, which installed without tools in about one minute. But a few weeks ago, we lost the burner in the other cartridge. I emailed PartSelect, and even though I gave them my obsolete model number, a helpful service rep managed to find me the part number of the correct burner, so I was able to place my order. Once the part arrived, there was no problem replacing the burner. This is a simple operation we've performed many times when we need to remove the burner for cleaning.

Parts Used:

Standard Y-Frame Range Surface Burner

Paul from Foley, AL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

6 of 9 people found this instruction helpful.

Was this instruction helpful to you?

two large burners wouldn't heat or would smoke even after cleaning

i really wanted a new stove, but budget wouldn't permit; so just had to insert the new ones and they work great with level cooking.

Parts Used:

Surface Burner - 8 Inch - 2600W

Lois from KNOXVILLE, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Burners were becoming weak. Home Depot and Lowes did not have replacements.

Remove burners using my hands and replace new burners using my hands.

Parts Used:

Surface Burner - 8 Inch - 2600W

Standard Y-Frame Range Surface Burner

James from EDGEWOOD, MD
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

replacing the hold down clip for the burner

Started out removing the old clip that didnt hold burner element down anymore. It was a bit rough, since i was taking off a rivet. I used the screwdriver to carefully wedge the edges of the rivet upward so that i could get the wire cutters underneath it enough to snap the head off. After some fanagling for about 20 minutes, i popped it off. The rest of the repair went like cake, and i am soooo thankful that the replacement part i ordered from you included a screw and a nut. Next time, if there is a next time, this repair could be done in 2 minutes. THANK YOU FOR SAVING THANKSGIVING AND A $100 REPAIRMAN SERVICE COST FOR A $10 PART!!!

Parts Used: