TEF367CCSD Tappan Range - Instructions

Using a socket set and Robertson #3 (smallest) driver head,with the breaker shut off before working I removed the old element and disconnected the old element from the wire connections.I then installed the new element by connecting the terminals to the wire connection in the range before screwing the old retaining clips to the back of the oven compartment wall.Then I flipped the breaker switch back on and turned on the oven dial to 425 degrees to see the element heat up and glow red affirming the success of the repair.Total time to repair about 15 minutes.

The bulb has a plastic clear cover. That cover can just be carefully removed using a screwdriver. It's held in by a metal bracket. After you remove the cover. You'll just need to replace the bulb and then re-install the cover and bracket.

Very simple. Removed oven rack that had melted residue on it and replaced it with the new one from your company. I want to tell you that the delivery service I received was just geat. Took less than 48 hours to arrive at my home from the time I placed the order on line. Keep up the good work and I will be happy to share my experience with those in need of you services. Thanks. Marilyn Kasson

First we turned off the electic, then we took the back off the stove and pulled the wire off the bad element then replace the new element. It was very easy to do.

I follow the video on your site

Unplugged the stove first !
Removed bake element ; (2 screws), looked OK,
measured with an Ohm meter, measured "open".
Also, removed rear cover (6-screws), wires not burnt. Ordered new element-rec'd next day! My wife installed it and replaced rear cover. Works great (oven!) and about $10 cheaper and quicker than from a local dealer!

First I removed the oven door from the range by removing 2 screws from the door. Next I removed 2 more screws from the oven door to get to the panel beneath. Once the top portion of the door was removed there were 4 nuts holding the glass sections together. Once these nuts were out I removed the broken class, replaced it with the new glass and reassembled. It was a very easy and quick project. I was so happy to find the part. I thought I was going to have to buy a new range. Thanks.

Very easy just had to pull the wire up that holds it secure.

Got a copy of the parts breakdown for the oven door from partselect. Com. Removed 8 screws from outer frame (3 top, 3 bottom, 1 on eah side). Removed the main glass pane from oven door, be careful when doing this as this is most of the weight of the door. It will want close on its own due to lack of weight. Removed the 2 top screws that attach the handle. Removed some screws from some plates that retain the 2 panes of glass of glass. Removed the third (most inner, broken) pane of glass. Replaced with new one. Reversed disassebly procedure for assembly.

I had open back cover and remove the switch than replace new switch. Makesure cable conection.

Unscrewed screws in back of oven holding element. Slipped old element off of wire. No need to cut wires has the kind of ends (spade ends I think they are called) that just is pushed on to element. Attached new element. slid wires back into wall of wire rescrewed to oven wall. Very easy just be sure wires don't get pulled back into back wall of oven. Don't know what you would do then.

I watched the video of the repair. It was very easy; removed 2 screws; disconnected 2 push-on tabs; removed the element; and then reversed the operation. Be sure to turn off the circuit breaker that powers the oven before you start the repair. Turn it back on when finished and test the oven.

I simply followed the instructions in your video. i shut down the power to the oven via the breaker panel, removed the two quarter inch screws with a nut driver, pulled out the old element exposing the two wire leads,disconnected one lead at a time and duct taped each lead to the oven wall,. Then removed the old element and replaced the new one in reverse order. Voila! It works great. This is the second element I replaced in this oven over the years. This site was prompt on shipping the new element (about 3 days since I ordered on a Sunday).. It was well packed and arrived on time and I even got an e-mail letting me know it arrived! How cool is that?! I've been a customer for a few years now and plan to be a "forever" customer. Thanks for saving the day! You ROCK!

Drank a beer, grabbed a screwdriver & tried to remove the two screws that held the element in place. The screws were old and when I turned them, they stripped instantly. This required another beer. Eventually I used pliers to grip the sides of the screws to remove and reinsrt them. When I finished the oven worked great, so I celebrated with another beer.

I was forced to call in a pro repairman. Will cost me at least $150 for part and repairman. I could have done job if instructions on how to rewire had been included.