Quick Question!

Have you ever purchased from PartSelect.com before?

Models > SWXG831HQ2 > Parts

SWXG831HQ2 Westinghouse Washer Dryer Combo - Parts

All parts for the Westinghouse Washer Dryer Combo SWXG831HQ2

Below is a list of all parts for the Westinghouse Washer Dryer Combo SWXG831HQ2. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the SWXG831HQ2
1-14 of 194
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$21.00

Drum Glide - White

This white drum glide is used in a clothes dryer to ensure the front of the dryer drum is supported as it does rotations. *Please note: these are sold individually, however there a...

$2.41

Drum Support Bearing

If your dryer does not tumble, will not start, is noisy, or is leaving marks on your clothing, you may need to replace the drum support bearing. The drum is supported at the rear by a bearing, which attaches onto the inside of the rear panel of the cabinet. You will need to remove the dryer drum before completing this repair. Although replacing the drum support bearing is a fairly easy job, you will need tools to complete it. For this repair, you will need a putty knife, a Phillips screw driver, a 5/16 nut driver and maybe a small flat blade screw driver.

$13.55

Drive V-Belt

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer,...

$21.15

Lint Filter

This lint filter is used in dryers. It works to collect lint and debris when it passes through the dryer vent. Air flow is necessary for the dryer to function properly and consistently, therefore it is crucial to clean your filter before every load. If your filter has tears, rips, or your clothes take too long to dry, make sure to replace this part to resolve these problems. As a safety precaution, remember to unplug the dryer from the power source and wear work gloves before beginning this installation.

$9.38

Thermal Limiter - Limit 220

The dryer thermal limiter, also known as a thermal fuse, blows the fuse to cut off power to the dryer when the dryer begins to overheat. Once the dryer reached 220 degrees Fahrenhe...

$8.90

Multi-Rib Drum Belt

The multi-rib drum belt is also known as a drive belt and is a part for your dryer. The function of the drum belt is to attach to the motor pulley. It will then spin the drum as the motor rotates. Over time this part will naturally dry out. If your drum belt begins to crack or break, the dryer will not be able to continue to turn. If your dryer is running but your belt will not rotate, that likely means that it has been damaged and needs replacing. The tools you will need for this repair are a putty knife and a screwdriver set.

$13.56

Lower Front Felt Seal with Adhesive

The lower front felt seal with adhesive, also known as a drum felt seal, is used in dyers and allows the drum to easily glide on the front panel. For this repair project, you will ...

$29.32

Door Catch

The door catch on your dryer is an important part as it keeps your dryer door closed, in order to ensure no air or clothes can escape. This part works by holding the door strike, which allows the door to stay secure. Before you begin this repair make sure to disconnect the power supply to the dryer. The tools you will need for this installation include a Phillips screwdriver and a small flat blade screwdriver. A pair of pliers may also come in handy. Users ranked this repair as easy, and say that it will take fifteen minutes or less to complete.

$14.16

'M' Series Ignition Coil Kit

This kit contains two coils, one is a two-wire secondary coil and the other is a three-wire booster coil. Both coils in the ignition coil kit should be used together in the clothes...

$102.69

Drain Pump - 120V 60 Hz

This is a 120 volt, 60 hertz drain pump that is manufactured to remove water from the tub of your washer once your clothes are washed. This part is the pump and motor assembly, which includes a red flapper to prevent drain backflow. You will need to remove the front panel of your washer to access the drain pump. The tools you will need for the repair are a Phillips screw driver, a putty knife, a pair of slip joint pliers, and a 5/16 nut driver. Be sure to disconnect the water supply from your washer before doing the repair. The metal edges on the appliance are sharp, so use work gloves to safely complete the repair.

$14.48

Front Upper Felt Seal with Adhesive

$5.92

Screw-In Plastic Leveling Leg

This is a screw in leveling leg for your washing machine. It supports the appliance by screwing in place to create a stable and flat surface. Take note that you are able to adjust the height of your appliance to make it leveled. This model is made entirely of plastic and is white in color. It is just under 2.5 inches long, 1.5 inches wide, and the head has a diameter of roughly 1.5 inches.

$19.48

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the...

$47.23

Ball Hitch

This ball hitch provides support to the drum located at the back wall of the dryer. This allows the drum to spin. The bearing may have gone bad and you might notice that the ball is cut off. The ball hitch might need to be replaced if you notice that your dryer is extra noisy, is not tumbling properly, or will not start at all. The ball hitch is made of metal and measures 5 inches in diameter. This is an OEM part that is sourced directly from the manufacturer.

All Parts for the SWXG831HQ2
1-14 of 194