SWT210WA1124 Speed Queen Washer - Instructions

Screw broke lose in agitator from drive bell stripped (plastic) for transmission gear. Received new Drive Bell and had to lightly cut out old from Agitator housing with saws all, cleaned years of soap build up on steel spline with wire grinder, lubed the Drive Bell inter and pounded on to spline gear with rubber mallet, I thought a bit too much force but what the heck I landed to the same bearing point as before. Work Out Great.

Hardest thing was moving washing machine away from wall. Two screws on panel. One screw for hose.

After receiving the new hose we replaced the hose and tested the washer by running a rinse cycle. The new hose fixed the problem.

checked for unbalanced load. still banging. removed lower front panel by removing 2 screws. then removed front top panel- 2 more screws. turned unit on spin cycle to see what was going on. this is dangerous as many moving parts are exposed, so keep everything clear. banging was the tensioner slamming back and forth. unpluged washer from outlet and felt along the belt to find part of the 'v' shaped balt had come part, leaving a gap in the "v". ordered part.when i got the part, i removed 4 larger bolts that held the motor, pully, and pump. i unplugged the wires for the motor, and removed the belt from the bsket side pulley assembly by slipping it off and under the shaft. i removed the torx screws that held the pump on the motor and removed the belt. PAY ATTENTION to how the belt was in between the pully and pump assembly or you will have to remove and redo it. reassemble the pump over the belt, pully, motor, and put the belt on the drum side pully before bolting it to the washing machine. it is fairly heavy and tight, so you might need help. this was not hard and you do not need to take apart the washer except for the two front panels and the motor assembly. i just pulled the unit away from the wall and tipped it back to access the inside. take your time and pay attention, and make sure it is not plugged into the wall and you should be fine.

Followed video on PartsSelect website, they made it real easy.

Removed front lower panel, removed 4 bolts holding motor, removed water hoses draining water into a pot, unplugged electrical connector on motor, removed motor, removed water pump from motor (torex bit), separated pump from motor. installed belt reassembled washer in reverse order. To my surprise, it worked and was easy.

Removed old hose by sqeezing clamps and sliding off of fittings. Placed clamps on new hose. Slid hose on fittings. Repositioned clamps over end of hose. Job done.

Replacing the spin belt is like the others have said, but I'll add a couple of cautions. Don't try to separate the driven pulley on the water pump from the pump shaft. Instead, separate the water pump from the driven pulley. And, make sure you know the routing of the belt for reassembly, because it has to go between the correct legs that support the water pump. Get it wrong and you'll have to start all over. I pulled the machine away from the wall by about 18" and put a block of wood under the front of the machine to raise only the front to 9" or 10" off the floor which made it easier to do the work. Try and take a digital photo of the belt routing from a couple of angles before beginning. Don't forget to route the belt around the tensioner pulley.

Basically you have to remove the drive motor and pump (in that order). This allows you to get the belt around the drive motor pully wheel. It took me a few tries to get the belt routed right. I assume that if you know what you are doing you can complete this in under an hour. It took me about 4 hours, though - cause I didn't know what I was doing at first. Hehe.

Hope this helps.

it was easy

Found out that these switches go from time to time and are usually the culprit when the washer won't operate. Opened the cabinet facing. Warning: there are plenty of YouTube videos on opening Maytag washers. None helped me with this model. I ended up finding the screws to open near the floor on front. Once it's opened, just replace the faulty switch, reconnect and you're in business. Getting the washer opened was about the hardest part of this repair. Total cost: Less than $30.

tilt the washer back removed bottom panal .removed bracket holding motor took motor out removed 3 scewer holding pump. took belt off put new one on. about 45 mins pretty easy job

I was at work but a friend of ours and my husband did the repair. But what I was impressed about is how fast we got the part. thanks a lot

Wow! My husband and I researched the problem online and ordered the part after reading from others how to take the machine apart. We are very unhandy, so we felt quite an accomplishment fixing the drain hose with rubber elbow ourselves! Thank you for the diagrams that so clearly showed the part we needed to order.

remove front cover disconnect water supply remove hose clamp,take drain line replace with new hose reconnect water supply replace front cover job complete.