SMH9151ST Samsung - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
I picked up a used microwave that came with the needed mounting plate but no screws
Based on my research, this over the range miscrowave should have come with 2 templates: 1 for the wall and 1 for the underside of the wall cabinet. The challenge was to measure every very aspect of that microwave in order to obtain placement specs for the mounting screws. Tip: I made the holes through the top cabinet bottom a little larger than needed and used big washers with then for stability to gain the most "play" in the self aligning screws. Worked out well. Took 2 tries to get the wall plate perfect so have precision in mounting that piece.
Parts Used:
-
AMANDA from ANKENY, IA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Glass broke
-
Frances from CRESCENT CITY, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken carousel plate
-
Peggy from RENO, NV
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
microwave door
We did not use the part, the spring fell off inside the door. We kept the part just in case
Parts Used:
-
SANDRA from GLENDO, WY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door latch broke off
Use knife to peel back molding around latch openings. Pull down on plastic latch part, pull out bottom and tilt up to remove broken part from spring. Tilt top of new part inward and connect tab to spring. Push in bottom of latch and snap. Replace the molding by pushing all around the door frame.
Parts Used:
-
Matt from Oswego, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The plastic door key (latch) broke where the spring attaches.
I took off the inner plastic frame of the door, removed the broken part, hooked the spring up to the new latch and replaced it into the proper alignment holes, and works perfectly. It was less than a 5 minute repair.
Parts Used:
-
Dave from ROCHESTER, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door did not stay latched
After removing the door from the OTR microwave, we slid out the old latch, slid in the new, & reattached the spring. Replaced the door & DONE.
Parts Used:
-
Dianne from Danville, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door latch broken
Used a putty knife to take off the edging inside the door to have access to the latch. Put the new part in and attached the spring. Replaced the edging and job was complete.
Parts Used:
-
Susan from Pecatonica, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door Latch Broken - Door Did Not Close
Got part from you in one day - great- watched utube video on removing molding and reinstalling. Video was longer than time to fix all need to do was remove molding and install the door latch - it is made of plastic with a hook on which to attach spring. Hook breaks and therefore door does not close
Parts Used:
-
BRUCE from LA QUINTA, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The door on microwave would not stay shut.
Called Maytag regarding the latch. Was told I had to order an entire new door that would cost around $170 before shipping and handling. Went on partselect and foundt he part for $2.02. Big difference in price. Very easy to install. Hardest part was getting the spring back on. Would definitely recommend to friends.
Parts Used:
-
Cynthia M. from Edison, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
no power
took THERMOSTAT;NT-101NA,250 out and put THERMOSTAT;NT-101NA,250 in so easy got the part in LESS 19 HRS
Parts Used:
-
Glenn from Pedricktown, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!