SF369LEPT0 Whirlpool Range - Instructions

removed the worn out roller...inserted the new roller....tightened the nut...it was finished...this was without a doubt the most pleasent repair from start to finish..only took 3 days from the time i orderded the part to completing the repair...i would advise anyone to use " partselect.com" without hesitation

since it was the control knob, all I had to do was to push it right onto the stem, and it was finished. Using the web site to find the correct item was very easy.

I have removed this piece once before and painted it,
but it is difficult to prepare surface.

I tried to replace the part without removing the door
but had difficulty getting the screws to line up.

So, I took the door off. Forgot that you are supposed to jam
the spring hinges in the open position before you remove the door. Manual describes how to do this but picture is not very helpful. So I made two wooden dowels about 3/8" in dia by about 3/4" long. Opened the hinge with a screwdriver and jammed the dowels in place.

Door Trim went on easily and the oven door went back on quickly.

Surprised they don't make this trim piece with rust proof material.

Simply removed three screws that held the door trim in place. Once the screws are removed be carefull because the front door glass is held in place by the bottom door trim. Otherwise an extremely easy repair.

Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).

Bought new igniter.
Pulled stove from wall and turned off gas and disconnected power cord.
Removed oven racks.
Removed oven floor.
Removed heat shield/dissipater thing.
Removed 2 screws holding igniter to gas burner tube.
Disconnected the wire (this was harder than expected because igniter had only a few inches slack in the wires), took off back to try to find better access to wires, no help there, door was not easily removable so difficult to reach in with 2 hands to pull wires apart, eventually I got it.
Connected new wires.
Replaced igniter to feeder tube with 2 screws.
Plugged back in, turned gas back on and tested.
Reassembled heat shield thing, oven floor, racks.
Done.

Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.

Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

Remove;
Bottom drawer- pull open and lift up slightly when fully open then pull the drawer the rest of the way out.
Unplug ignitor terminal- there is a small tang inside the terminal end that needed pressed out of the small hole of the ignitor, with a pick.
Oven racks.
Oven bottom- 2 long phillips screws at the back. lift the back up 1st then the front comes up and out.
Burner diffuser- 2 small phlilips at front (they only prevent the diffuser from sliding, they don't screw into anything). slide diffuser forward out of the notch then lift the front up. pull rear tabs out of the notches to completely remove.
Ignitor- two 8mm (5/16) bolts holding ignitor to burner. pull ignitor out of guide holes.
Reverse to install new ignitor.

Remove three screws, slid old trim piece off door. Slid new trim in place. Used ice pick to align screw holes and replaced screws. Total time about 15 minutes. Tip: used a bead of silicone sealer on the new trim strip to prevent moisture from causing new strip to rust.

Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

Unplugged, took off back, removed old part, put on new part and connected. Replugged and it worked great.

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

took the handle off, replaces the side trim piece and replaced the handle. Very simple!

Turned off power to range. Removed the lower panel that was secured by two screws, as well as the metal cover beneath it also secured by screws.. Removed the two screws securing the igniter, and pulled apart the black tubing that secured the igniter. (I had to pull hard to get it apart). Plug the new end into that same black tubing. screw in the two screws to secure the new igniter (this is tricky because one screw is hard to reach) I laid something in the base to cover the holes so I wouldn't lose a screw if it dropped. Screw metal panel back in, followed by the lower oven panel.