SF367LSXQ1 Whirlpool Range - Instructions

removed the old ones.then installed the new ones.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

very easy

Screwed in light bulb and glass protector

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

My husband did this and he is not here.

take the 2 screws that hold the handle on out...watch the glass front and the side trims because the handle holds them on. Take the glass out then remove the side trims. Replace the side trims holding the glass in place with 2 pieces of masking tape om each side then install the handle with the 2 screws and remove the masking tape.

Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.

Install bottom door trim first...Remove upper door handle and set new glass door front piece in place and re install upper door handle and tighten all screws...Looks great

Using 4 strips of duct tape was useful,in holding the glass to the door.

Removed old trim kit and handle installed new parts but was having problems with glass fitting between handle and bottom bracket there was a gap between glass and handle when installed fist time after disassembling again I found that the door frame it self had to be tapped back into alignment to be square but once the adjustments were made the installation was a breeze

This repair is only if your old igniters are working but they are so cracked that the spark is not going where it should be. TURN OF THE GAS SUPPLY VALVE BEHIND THE STOVE AND UNPLUG THE STOVE FROM THE WALL.I had to drill out most of the old screws to remove the burners plates because of all the old baked on spills. I bought replacement screws when I bought the igniters because I felt this would be a problem. My repair time included scrubbing the stove top. Once all the parts that make up the stovetop burners were removed (NOTE WHICH BURNER PLATE CAME FROM WHICH LOCATION, THEY ARE DIFFERENT SIZES) and I could see the pipes beneath the stove top, I cleared off the top and used a spreading knife to push in the clips on the left and right sides near the front of the stove. It was thin enough to fit in the space between the stove top and main body. Push the clip inward and pull up on the stove top and it will let you lift the top. Be careful because it may release suddenly so be gentle. I also removed the top section of the back of the stove to access the igniter terminal block. A few screws, nothing more. Be sure to take note of which wire goes where. (They are color coded). Unplug the old igniters. it is easiest to cut he old igniters off of the end of the wires and pull out three wires leaving only one. At the back left of the top of the stove there is a rectangle channel that the wires are running through. There is a clip that holds the wires loosely together. Remove the wires from that clip or the next part will be difficult. Run each of the new igniter wires through their respective holes in the stove top. BE CAREFUL NOT TO DAMAGE THE WIRE INSULATION IN ANY WAY. When you put the burner plates back on the igniters will be sandwiched in between the plate and the stove top. Using electrical tape, tape the connector ends of the new wires to the one remaining old wire. Gently pull the old wire through the rectangle channel, pulling from the back of the stove. Take your time so no damage occurs. Once the wires are pulled, plug them in to their respective terminals and place the wires in the loose clip. Make sure the new wires are not crossing the pipe openings where the burners are located. You can close the stove top and double check there are no wires across any of the burner openings. Re-assemble the burners and plug in the stove. DO NOT OPEN THE GAS VALVE. Turn on the stove and check to make sure the new igniters are working properly and sparking to the burner plate assemblies. You should see a controlled spark. Do not touch the burner plates or igniters or you will be shocked. If all are working then you may put the back cover on and open the gas valve. If none are working make sure the stove is plugged in. If some are working then check the connection on the terminal block and the wire insulation. If they are still not working then you've got bigger fish to fry. Good luck my friend. Happy fixing!