SF367LEMQ0 Whirlpool Range - Instructions

The parts I got were exactly like the original knobs and were a breeze to snap on. Range working great again . The wife is happy again lol

1. Removed old knobs and the adapter piece with pliers ( I tried using cheap universal knobs from Lowe’s first that were garbage)

2. Push the new knobs onto the shaft and voila. Perfect fit and range looks new again. Replaced all 4 on my black whirlpool gas range

exchanged old with new

Remove the side covers. Remove the 2 screws on the back side of the door, hold on to the glass and front panel, they will fall out. remove the 2 screws holding the handle. Put the new handle in place and insert screws, note the old handle had metal inserts that are threaded, the new does not. Had to push very hard and let the screws bite into the plastic.

Remove old grate place new grate on gas stove top

Loosened two screws and removed tray, very simple. Replaced new tray and adjusted screws to hold tray. Easiest part was finding new tray part number and ordering replacement using online parts diagram.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.

Put the bottom of the glass in first then put the top half into the brackets in the door handle. Holding it in place with your extra set of hands tighten it down with the two screws from inside the oven door into the back of the handle. The door will be open a lot so be extra careful not to let the door close onto your hands or fingers. Also remember patience is a virtue.

I found the part via the internet called the contact number of partselect received the order extremely quick. contacted a repairan who never came so I took matters in my own hands. Looked the part over lined up the connectors, removed the panel behind the range instaleed te new part and voila. Thanks PartSelect for your assistance

Laurel

removed 3 screws holding the strip and replaced with new strip

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

Following details from the installation video, after removing the main gas line and the two output lines I removed the four screws that removed the valve but found it was easier to remove and install the new one if I first removed the oven burner(it made for lining up the valve nozzle to the burner easier) from the inside, 3 wires attach on the side towards the stove taking one wire from the old valve and putting it on the new valve in the same place. Everything went back together just fine, I did have some problem with tightening one of the two gas lines for the output and found I just had to keep tightening it a little until there were no bubbles appearing when I applied soapy water to the connections, other than that it was very straight forward.

new handle arrived black for white oven - screws did NOT fit new handle- glass came off the door when removing old handle

This oven probably was manufactured in the '60s when the house was built. The door doesn't just pull off like the newer models. These pins fit into small holes on the oven hinges. I inserted the pins and lifted the door to a 45 degree angle, before pulling the door completely off. Now that turned out to be the easy part. I then proceeded to completely dismantle the door. It actually has 4 glass layers which had to be cleaned individually. The hardest part of all was actually remembering how to put it back together again. I put the door back on just as I had removed it, then took out the pins, and I was finally done! This was not an easy project, BUT the results look great.

I had to unscrew the handle from the door as well as take out the front glass, put the trim in place (Thank God for the bottom placement nipples on each trimpiece), hold everything together after aligning all the pieces in place while I screwed the handle back on. The reason I was replacing the trim in the first place was that it is fragile plastic that had broken on both sides when I replaced one inner glass piece that had broken.