SB520K (P1140701W) Amana Refrigerator - Instructions

Viewed the viedo - it showed what to do

I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

I watched the online video and followed the directions. The only thing that was not obvious (and this is where the video saved several minutes)was how to remove the upper part from the door. This repair makes the door seals much more effective and should reduce the compressor run time. I have to compliment you on your prices and speed in getting the parts to me...great service!

First My Frig side of the double door unit wasn't closing on its own. Kids don't look, so they walk away...next thing you know the frig warms up and the freezer starts to frost up from running so long...Now it won't shut off.... I checked the hinge and sure enough it was wore down. Now mind you, I ordered a hinge kit first without checking to see what type I needed...don't do that...Less than 15 mins you can take the door off and see which one you need.As soon as I saw which type of hinge set I needed I went and ordered it...returned the other one. It came pretty quick.... 15 mins had that sucker changed and working... But... the door still wouldn't close on its own... Common sense told me the heat from the frosted freezer caused the door and frig walls to swell... Yes I said the heat... When the component in the freezer frosts up it does not keep the frig cool, nor will the freezer stay kool... the frost prevents the cool air from moving around...thus "HEAT".... It took a full 24 hrs for my frig n freezer to get back to normal... and now the door closes just fine... MIND YOU! I had to take the covers off the freezer unit inside, then take a steamer and melt all that frost off of every inch including down the drain... That took me a good 5-6 hours... and what a mess.... but it was worth my time.... because I don't have to replace my second hand Jenn-Air which I could never afford to buy brand new.... Whew....what we have to do to keep things going... $11 bucks worth of parts.... "Super Mom" :o)

remove right door replace lower door cam

I was very pleased with the entire experience. The part was easy to locate on the web site, it arrived very quickly and you sent a how-to video.

took the door off the hinges laided flat and withcordless drill and socket took the gasket off and replaced it with new one

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.