Models > S166-C > Instructions

S166-C Jenn-Air Wall Oven - Instructions

All Instructions for the S166-C
286 - 295 of 295
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
door wouldn't close well for 3rd time
I had repair men replace the door hinges 2times and decided the 3rd time to do it myself and save some $. ordering was a chinch, received the parts in 2 days and followed instructions posted on this site. They were excellent. Just a few things I would stress: Lift UP the door to remove, not open the door fully and pull out and also make sure to take the small pins out of the new hinges before closing. They are so small you could over look them. The person who put detailed instructions on this site is to be commended for clarity and detail on "How To" I really appreciated it.
Parts Used:
Door Hinge
  • Barbara from Reno, NV
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burner would stay on high, on all settings.
In response to your question.......everything went perfectly!! The reason?? I read the directions that were very easy to follow. It was a quick, easy repair, and the stove burner is working like new.

Thank you for your help!!

Bob
Parts Used:
Surface Burner Switch - 240V
  • Robert from Attleboro, MA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Burner always on high, no temp. adjustment.
Removed 4 screws, tilted cover up and lifted out, removed wires from switch, removed 2 screws holding switch, lifted switch out. Replaced with new switch, connected wires, secured cover with the 4 screws. It worked!
Parts Used:
Surface Burner Switch - 240V
  • Woody from New Castle, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven wouldn't heat to temperature
Turn the power off to the oven. Removed two screws on the back of the oven which held the element in place. Gently pulled out element and unhooked it from the clips. I then got the new element and hooked it back into the clips. I pushed it back in and replaced the two screws. Restored the power and turned on the oven. It works like new!
Parts Used:
Bake Element (16 Inch long x 19 Inch wide)
  • Debbie from Fremont, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Frozen screws
Followed instructions. Two screws frozen. Unable to loosen. Forced to grind heads off and replace with new screws.
Parts Used:
Oven Door Seal
  • Jack from Lake Wells, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Left Rear Burner would not work
Shut off breaker, removed the top by unscrewing the retaining screws and removing all knobs and grommets. Removed control from top panel by unscrewing, removed 5 wires and placed on new control. I then remounted the control, placed the top in its well, fastened. Replaced the retaining screws in the hold down strip and replaced grommets and knobs. Returned power to panel by turning the breaker on and tested. Used later that evening to grill 2 panini.
Parts Used:
Surface Burner Switch - 240V
  • Sharyl K from Nampa, ID
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
range installer broke a screw off & busted the plastic piece
Had to screw off old terminal block & screw on new one
Parts Used:
Main Power Terminal Block
  • Christina from West Des Moines, IA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Filter element missing screen material from age and cleaning
Lifter grill and replaced filter. It fit perfectly.
Parts Used:
Grease Filter
  • Harry from Bedford, VA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Oven not heating
Ordered oven element. Had to use liquid wrench to loosen screws holding element in place. replaced, It works. Now the top left burners don't heat up.
Parts Used:
Bake Element (16 Inch long x 19 Inch wide)
  • George from Atwoter, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
switch was broken
simple repair 4 nut screws easy
Parts Used:
Rocker Switch
  • don from gardner, KS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the S166-C
286 - 295 of 295