Quick Question!

Have you ever purchased from PartSelect.com before?

Models > RUD5750HB0 > Instructions

RUD5750HB0 Roper Dishwasher - Instructions

All installation instructions for RUD5750HB0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the RUD5750HB0
121-135 of 222
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

leaking dishwasher

  • Customer: Wendy from Bozeman, MT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
pulled out the old seal and put in the new, fixed the leak!

Leaking water from front door

  • Customer: Lanny from Montevallo, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video and did the repair it was easy.

Dishwasher lower rack - rusting

  • Customer: Eleanor from Elko, NV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Took out old dishwasher rack and replaced with new.

Old part was broken

  • Customer: Patricia from Yucca Valley, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
I am a 64 year old female and replacing the broken Access Panel was fairly easy for me to do without help. The hardest part was separating the metal bottom part from the broken plastic part in the old access panel. I had to break the plastic away from the metal section using pliars. That took me almost 10 minutes. Slip the decorative plastic facing out of the old piece and into the new one. Attaching the metal piece into the new panel was a "snap". The bottom screws do not need to be removed. Just loosen a bit and slide the new unit onto them. Then using a nut driver screw in the two top screws and then tighten the two lower screws. Now the unit looks like new.

Leaking from bottom of door

  • Customer: Michael from Marietta, OH
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The hardest part was locating the leak. After consulting the other repair suggestions, I concluded that the gasket was a little more worn on one side than the other so I ordered the gasket. The evening before the gasket arrived (quick delivery from partselect.com) I decided to shim out the old gasket with some old door insulation. It made the door harder to close but it didn't leak any more. When the gasket arrived I replaced the old with the new. It leaked more than ever. After reading more repair instructions, I decided to take apart the door vent and check it. It was packed solid with gunk. After a good cleaning, I put everything back together. No leaks! I tried every repair listed except the door vent. Guess steam is a good gunk conduit LOL. I supposed I didn't really need the new door gasket but I can tell the door has a tighter seal now. Here's a tip to watch for. If the door doesn't leak right away after the washer starts, take the door apart and look at the vent. It can look just fine from the outside and that's deceiving. Someone else mentioned the 'leak' timing that finally got my attention and lead to the 'fix.'

Plastic edge broke off

  • Customer: Margaret from Amboy, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Lower panel was easy to replace. Had to apart the trim on the old one and glue. No problems at all. Glad to be able to gets the part to fix. One of the plastic edges that holds the screw broke.

spray arm would not clean

  • Customer: Anita from Weatherford, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took the old arm off in a minute and replace with the new on,total time about 5 minutes and it now works great

Stopping in the middle of cycle. Finally quit completely.

  • Customer: Robert from Sacramento, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Turned off power to dishwasher. Removed inner door panel. Cut wires as directed and installed new switches. Also installed new spring on soap door opener. Reassembled, ran and tested. Take your time, this repair is pretty simple.

machine leaked from the door

  • Customer: SY from GOODYEAR, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
easy to remove the old gasket but did not solve the problem door leaks from the bottom and water remains on bottom of machine

Leaking Around Door

  • Customer: KATHY from BLYTHEDALE, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Opened the door removed old seal and put the new one in. The only hard part was getting the new seal out of the package. It took about 1 minute to do. Very easy.

Dishwasher door panel old and buckling

  • Customer: Frances from Fairfield, CT
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Amazing how quickly the part was shipped and arrived. Very easy to install no tools needed.very pleased with everything . Thank you.

Dishwasher was smoking.

  • Customer: Jason from Gilbertsville, PA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced the heating element that I ordered from Part Select. The repair cost me less than $25.00 and took me less than 5 minutes. I saved $650.00 by not buying that new dishwasher that my wife wanted to replace it with. I'm sure she will find some way to spend the money I saved(lol). Thank you Part Select.

soup lid spring and pin broken, wouldn't pop open

  • Customer: Heather from everett, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I just followed the video, and it now works perfectly! Thanks SOOO much! great site, great info.

Failed to get dishes clean

  • Customer: Wayne from Baltimore, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
Shut off water supplyand removed front cover below door. Remove flexable water line (wrench set), valve and bracket (nutdriver), and input hose (pliers). Installed flexable line on valve, replaced input hose on valve, then installed valve and bracket. Found screen on input to valve almost completely blocked with buildup of materail. Replaced front cover. result, bright, clean dished.

leaking around door

  • Customer: Curtis from Enderlin, ND
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
After cleaning the filter located on top left of door(used a screw driver to pry out) and following the install gasket video problem solved.
All Instructions for the RUD5750HB0
121-135 of 222