All Installation Instructions for Roper Refrigerator RT20DKXDW02

changed the light bulb still would not work so I figured it was the switch sure enough.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Parts Used:

Refrigerator Door Switch

anthony from HAVELOCK, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

defective light switch

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Parts Used:

Refrigerator Door Switch

THOMAS from WILLARD, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

the light socket broke apart

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

Parts Used:

Light Socket Kit

Elyse from Skokie, IL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Broken Refrigerator door retainer

This job was extremely easy, snap on.

Parts Used:

Refrigerator Door Shelf Retainer Bar End Cap

Leroy from IRVINGTON, AL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Faulty light socket

Followed the video instructions.

Parts Used:

Light Socket Kit

Larry from HOUSTON, TX
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Drain clogging causing water to leak bottom of fridge

After watching videos how to replace went very easy.removed ice maker cut wires replaced switch put back together now working ok so far.

Parts Used:

Refrigerator Bimetal Defrost Thermostat

Ted C from DSRT HOT SPGS, CA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Door light switch disintegrated

Very simple fix, remove 3 screws, two connectors to the old switch

Parts Used:

Refrigerator Door Switch

Thomas from Roseville, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Could not properly open the door wirhout the handle

I Clean the handle both top and bottom. I place the cap in place on the bottom of the handle and tap it in snug with a hammer. I then place the top of the handle back into it's original position and then I screwed the end cap in place at the bottom. EASY !!

Parts Used:

Handle End Cap Kit

Kenneth from Neptune, NJ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Light didnt go on

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Parts Used:

Refrigerator Door Switch

dorotea from staten island, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

The handle broke and my wife was afraid to close the door because she might not be able to open it back.

The part-select video showed me to do the following:

Unplug dish washer

Open the door and unscrew the screws around the inside of the door all around.

Place the screws in the detergent holder with a cap until finished.

The door mechanism is at the top and attached to two electrical wires.

Unfasten the wires from the attachment.

Take the new attachment and fasten the wires to it.

Place the attachment back in the spot and make sure handle is sticking thru the hole to the outside.

Reattach the screws.

Plug back chord.

Finished - 15 minutes

Parts Used:

Refrigerator Crisper Drawer Glass

Jeff from WINSTON SALEM, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

After 17 years, the old door gasket was split and showing signs of mold

The gasket has an inner lip that fits over the edge of the door plastic liner. The old gasket was removed by pulling it straight out, in the plane of the door. Try not to pull sideways as it could crack the door liner, which gets brittle with age. The new liner had a brown magnetic strip, which holds the door closed, and this fits behind the edge of the door liner. Start on the bottom of the door. A helper is useful to hold the gasket loosely vertical. A flat blade screwdriver can be used to pry away the liner to insert the new seal. Once you have worked in the lower edge, install both sides, and then the top. Some juggling side-to-side may be needed for an exact fit

Parts Used: