RK966G310 Hotpoint Range - Instructions

Piece of cake to repair. I took both both heating elements off. I sprayed oven cleaner everywhere to soften the grime. I waited 10 minutes and wiped up the softened baking grime. Installation took 5 minutes for each element and about 15 minutes to clean the oven while both elements were removed.

removed 2 nuts holding the element in the oven. removed 2 screws that secured the wires to the element. installed the new element in reverse.

I removed the two screws holding it in place,Then pulled it out so
i could remove the two wires , then connected the new unit. Replaced it in the oven wall.
Turned the oven on and it worked like a new one.

Removed the two screws that held the element in place. Pulled the unit out a few inches to get at the bolted wires. The hard part is reaching in the oven using bifocal lenses and trying to block out the oven light. Getting past that obstacle, the rest went very well.

Toughest chore was to find a tool to remove the two hex screws that held the element to the back of the oven. Once I found the proper tool, the rest was easy. Pulled the circuit breaker, removed the two hex screws, disconnected the two electrical leads and put the new part in and did everything in reverse. Probably saved over $100 doing it myself.

Turned power off to oven. Unscrewed back plate exposing wires connected to heating element. It was difficult to unscrew the connections between them as it was hard to reach in because the oven door was in the way, but i finally succeeded. Unscrewed the bracket holding the burned out element and then attached the wires to the new element. Attached the bracket and I turned on the power. I then tested the oven and it worked.

Removed two screws that held the element flange onto the back of the oven, then two more little screws that held the element tips to the wires in back. Installed in the reverse sequence in about 10 minutes. A whole lot cheaper than calling a repairman! Thanks, the PartSelect customer service lady was a great help in getting me the right part for a 20 year old oven too.

as you explained in the e.g.
it was the easiest thing to do for my husband, and in 10 minutes I was able to bake again.

Thanks so much for the fast delivery!!!
Sincerely Rosemarie Ressel

First, I turned of breaker for the appliance. Removed two hex head (1/4") screws that hold element in place at back of oven. Gently pulled element exposing wires connected at base of element by hex head screws. Removed the screws and olf elelemt, placed new element in place, tightened screws, inserted into base and tightned screws for plate that holds element. After turning on the breaker, I set the oven to a low temp so I could feel the heat without burning my hand and was satisfied that the element worked.

Ordered the part on Fri. AM and it arrived Sat. PM! Could not believe how quickly it arrived. Husband replaced the old element and I am baking again! Thank you.

Turned off power at breaker and removed old element and replaced new element.

No instructions provided, but not needed. Removed two screws holding element in place. Removed two screws connecting element to power wires. Installed new element using reverse process.

I removed the plate held by 2 screws that holds the element, pulled the coil out and disconnected the yellow and red wires. Removed the broken one and connected the new one. Very simple. I also would like to add that you people are great to deal with and I will tell everyone to buy parts from PartSelect. Your service is outstanding and fast. Thank You.

The repair was very, very easy. The hard part was locating the part. I could not find it at any local hardware store. Went on-line and ordered part with PartSelect.com and it was at my front door the next day. The job was done in less than 15 minutes later. Thank You

After checking the website, I wasn't sure the part I needed was available. Called the Customer Service number and the lady was very helpful.
My part was delivered in 2 days regular UPS.

The most time took finding which breaker shut off the power to the oven. Removed two screws on the inside of the oven at the back wall. Pulled out the wiring and removed two more screws that attached the power to the element. Replaced the old element with the new one. Reversed the process. Done in 12 minutes! Very easy.