RK767G*T7 Hotpoint Wall Oven - Instructions

I turned off the breaker to the oven. Removed the old element and replaced. Turned on the oven breaker and turned the over to 350 and it was working great. I was very proud of myself as a 68 year old widow.

USE A MAGNETIZED SCREW DRIVER. BE CAREFUL THE OVEN ELECTRIC WIRES DO NOT FALL BACK INSIDE OF THE OVEN. HAVE LONG NOSE PLIERS HANDY. MAKE SURE YOU TILT THE ELEMENT SO THAT THE ELEMENT TERMINALS ALIGN PROPERLY WITH THE THE SCREWS AND ELECTRIC WIRES. THAT'S IMPORTANT ELSE YOU CANNOT GET THE SCREWS STARTED TO ATTACH THE ELEMENT.

Turned off the power to the oven. Removed the racks. Removed two screws holding the unit to the back of the oven. Removed two screws holding the wires to the terminals. Removed the old unit. Reversed the process. Piece of cake. The only "difficulty" was that the old wire-to-terminal screws required a nut driver (as did the unit-mounting screws) while the new wire-mounting screws required a #2 Phillips screw driver. Took me a couple of minutes to get one of those from the garage.

Two 1/4 inch screws and then two Phillips head screws that was it

Removed the nuts securing the element to the back of the oven, pulled out the wiring and unscrewed the wires. Went on line and found the part, ordered it, received really quickly and put the part back in the oven. Works great. Oh, I also turned off the power.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then I connected the two wires to the new element with the screws provided and simply replaced the screws that hold the element in place.
In 20 minutes the job was done. It was a snap to make the repair!

Turned off the power to the stove, pulled out the racks, unscrewed the old element and pulled off the electric connectors...easy so far...installed the new element to the electric connection, pushed back into the back of the stove and reinstalled the screws. Turned on the power and then the stove...now I can bake an apple pie!

Removed old new one fit perfectly

As instructed in your directions

removed parts from carton,,shut off breaker to over,,cradled the flash light,removed cover plate,,removed element,,removed screws from wires,,reversed to install,,screwed wires to element,,placed element in place and installed plate nuts,,,turned breaker back on...

Removed door. Take out two hold down screws for element. Hold electrical tab with pliers and remove screw on each tab. Reverse directions to reinstall. Door may have screws to remove.

Turned off power. Then loosened two nuts at back of oven. Pulled out old element and inserted new element. Tightened two nuts and turned power back on.

Simple, unscrew and then re-screw

I removed the two screws that held the element panel on. I removed the lead wires from the element, making sure the wires didn't retract back into the wall. I put the new element in, reconnected the lead wires and put the screws back in. I was concerned that the panel wasn't as long (top to bottom) as the previous one and it barely covered the hole, but it works fine. It would have cost me $60 to have it done by my home warranty company so I saved almost half.

First, I shut off the power to the oven... no point in risking a nice electric shock. The next thing I realized was I could not see anything... enter the flashlight. Then, well then it was really easy. I removed the two screws that held the element to the back wall of the oven, pulled the element (and some of the insulation stuffing) out about 2 inches to reveal the two wires and their connecting screws. Unscrewed them, put the new element in, reconnected the wiring, restuffed the stuffing and reattached it to the oven wall. Turned on the power and she heated up faster than ever. Speaking of fast, my part arrived the day after I ordered it and that was with regular shipping. Thanks fellas.