RK384J4 Hotpoint Range - Instructions

Moved stove from wall, unplug the stove from the wall outlet, remove the oven racks, unscrew the plate against the oven wall supporting the element with a small adjustable wrench, pull out the element slowly without tearing the insulation & stretching the two wires, unscrew with a phillips screwdriver each wire with care, as a precautionary measurement: do not make contact with the other wire and any other part of the stove, even though it was still unpluged. Install the new element in reverse procedure...turn on Bake Element on low temperature..when it glows when hot..ready to go.

Took oven door off. Removed screws that were holding oven insert. Pulled out oven insert. Removed old gasket. Installed new gasket. Push oven insert back. Installed screws. Replaced oven door.

Son-in-law unscrewed oven compartment; broken gasket was easy enough to remove and new gasket easy to replace; only problem was oven door would not shut tight. Tried shoving gasket harder into groove, tried turning on oven and heating new gasket to see if it would soften. Finally got it to close by pushing hard on left side of oven and inside light would at least go off and stay off.

shut off electricity to the range, removed the screws holding the element in place, pulled the element out as far as it would go, removed the screws holding the wires in place, tossed the old element, attached the wires to the new element, pushed the element back into place and reattached the screws holding the element in place. Turned the electricity back on and the oven heated right up.

Also, the part arrived the day after I ordered it. Great Price & Great Service.

Removed racks from oven. Each element had two screws, used socket wrench for all, gently pulled out element to exposé wiring removed wires with same socket. Once element out of oven, reattached wires to new element, reset element to back of oven and with the two screws attached back. Did the same process for top element only exception was a bracket holding top element from leaning down. It had two screws all the same size as element screws. Once all back in place turned on breaker to check each element.

pushed on the new knobs.
thanks fore having the parts.

1. Make sure electricity is off!
2. Remove 2 screws at rear of oven where the bake element is attached.
3. Pull out far enough to remove the 2 screws where the wires attach.
4. Lift out the old element and set the new one in.
5. Reattach the wires.
6. Reattach the element to the rear of the stove.
7. Turn electricity back on.

Easiest thing I've done. Shut off breaker. Unplug range. Pull out from wall (because this is a good time to remove the back, clean under and around the unit, check out the insulation and electrical contacts....or skip it, whatever). Open oven. Remove door (while ajar, pull up). Remove racks. Unscrew mounting plate from back interior wall. Set screws aside. Gently pull element forward until the leads and wires come through the insulation. Remove any strands of insulation that stuck to the leads and connectors. Unscrew leads. Keep left wire to the left and right wire to the right. DO NOT CROSS. Set screws aside. Discard old element. (This is a good time to clean your oven, if you haven't in a while.) If you cleaned oven, wait until dry. Position new element, feet down, in bottom of oven. Position left wire on left connector. Screw tightly BUT DO NOT BEND LEAD. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Position right wire on right connector. Screw tightly BUT DO NOT BEND. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Do not leave screws loose. Connection must be tight. Fire hazard, otherwise. If you bent nothing, then gently push element back through insulation until mounting plate is flush. Screw into position. Replace racks. Replace door. If you decide to check insulation and other leads, now is the time. I checked mine and it's a good thing I did.... Unscrew back plate of oven, keeping screws in order. Remove plate. Check that your new element and insulation aren't bunched up or otherwise in a hazardous state. You may notice burned or greasy insulation. You may see burned leads on light receptacle and broil element. If you do, then replace them, too. When finished with everything, replace back plate. Put range back into position, ensuring level and plumb. Plug in. Turn on breaker. Pat yourself on the back. You just saved $100-$250, depending on where you live.

Installed new knobs, mom is happy!!

Partselect made this job a breeze. Due to the user friendly process to order and receive the part. I repaired the stove after turning off the breaker in the main box. There were two screws that held the baking unit in place, removed them and then replaced with new unit.

Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!

I simply took the 3 new timer knobs and slid them on the metal shafts. It took less than 5 minutes to replace all 3 knobs. Now I can set the start, stop and time functions which have been inoperable for over 5 years. An easy and straight forward .

Removed old knobs and inserted new ones.

Repair went a lot faster and easier than I anticipated. Instructions are similar to those posted by others.
1. Verify that new gasket looks mostly like old gasket as best you can since not all of old gasket is visible.
2. Shut off circuit to oven (optional, but good practice)
3. Remove racks, trays, etc from oven to reduce weight at Step 7
4. Remove oven door by partially opening door to broiler position (about 20 degrees). Door should catch and stay open on its own. Slide up and lift off door. The “hinges” are spring loaded so carefully return them to closed position so they won’t snap shut on fingers.
5. Remove Phillips screws, one on each side wall of oven liner.
6. Remove two hex screws and metal gasket-holder on top center of oven liner.
7. Pull and slide oven liner out of oven mainframe about 1/4 “ to 3/8”. This may be the most difficult part of the job.
8. If possible to remove just a couple of inches of one bottom of old gasket (right side is easiest), verify that the cross-section profile of both old and new gaskets are essentially the same. If not, you have the wrong gasket.
9. Pull and remove old gasket. If gasket is dry and cracking, it may be necessary to scrape it out with putty knife, flat-blade screwdriver, etc. if it has fused to metal over the years. Note how it was installed on the metal edge of the oven liner.
10. Locate the mid-point on the new gasket length and begin inserting it at the top-center of the oven liner where you removed the two hex screws. Continue installing along both left and right sides of the liner. Each end of the gasket should extend to just above the respective hinge. No trimming should be necessary. Ensure a snug fit all along each side and top.
11. Push liner back into oven mainframe. Replace Phillips screws, gasket-holder, and hex screws.
11. Pull out each hinge to broiler position.
12. Replace door by sliding down onto hinges. Close door and check for tight fit against gaskets. Gaskets will flatten somewhat over time
13. Restore power, racks, trays, etc.

Removed 2 nuts holding the baking unit to the oven back, removed 2 nuts holding wires in place, installed new unit following procedure backwards. It takes longer to get the tools,take the oven door off, and take racks out than it does to remove and replace the baking unit.