RH962N2K2 Hotpoint Range - Instructions

1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

First I disconnected the power. Then I removed the burner element and drip pan. Using the screwdriver I removed the single screw that holds the terminal block in place. I then cut the 2 wires to the old terminal block. I connected the wires of the new block to the existing wires using the supplied wire nuts. Next I slipped the supplied heat shrink tubing over the wire nut and wires and using the heat gun I applied heat to the shrink wrap. Finally I reinstalled the new terminal block using the old screw and re-installed the drip pan and burner. I repeated the procedure for 2 other burners that were exhibiting the same problem. All work perfectly.

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

Snapped in place (4)

My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!

Very easy and simple/ After making sure power supply was off, removed socket screws in back plate of element, slid old element out, attached new element and replaced/tightened socket screws on plate and new element. Power on, oven on .. heated quickly and nicely. Used oven several times since ... no problems.

Ordered part, took old bake element out, installed new bake element. It was real easy.

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for my husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

A very easy fix-Unplug stove, remove back plate, remove non-working element and drip pan, unscrew terminal plug and push it through to back of unit to have room to work, cut wires to old terminal plug approx 4" from plug, inspect remaining wires for damage and if all is OK, strip old wires and wires of new plug approx 1/2", twist together and cap with wire nuts, cover with shrink wrap and warm with heat gun, push newly replaced terminal plug back into stove top, screw to terminal plug holder, replace back plate, plug in and replace drip pan and NEW element. Worked like a charm!

At 76 I no longer do my repairs so I asked my daughter's friend to do it for me.

Easily removed two screws, pulled the wires out of the oven wall, disconnected the old and reconnected the new, pushed it back into the insulation, inserted the screws and tightened them. There was a problem with the model number. It was on a vinyl plate inside the oven drawer wall. The plate was slightly yellowed so I used my finger to wipe the yellow away. When I did, the model number ended up as a black smudge on my finger tip. GE's engineers could have come up with a better method of displaying the model number. GE's customer service operator, however, did an excellent job of helping me to ascertain, at least, some of the number.

Removed 4 screw nuts and replaced with new baking element using same 4 screw nuts. Real easy job.

First I turned the power off to the oven/stove at the breaker box in the basement. Then I took the back plate off. Then I removed the two screws holding the wires onto the damaged element. Then I removed the two screws holding the element to the inside rear of the oven. Then I pulled the old element out and replaced it with the new element. I replaced the two screws that hold the element to the inside of the oven. Then I replaced the wires on the element where it protruded at the back of the oven. I put the back plate back on, slide the oven back in place and turned the power back on at the breaker and everything worked.

First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire connection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.