RGB790DEP2WW Hotpoint Range - Instructions

Straight forward as per instructions. Removed old igniter, replaced and tested new one and it worked. However, the gas oven would not turn of. Valve may be defective. Knob control is not stripped and turned to full stop. Troubleshooting continues. Part(s) and instructions worked perfectly.

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cover off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it

I figured out the problem, ordered the part, and replaced it. Four hex head screws, two wire nuts, and two thum screws latter it was working.

Go to utube videos for this are there

My husband removed the two screws t hat hold the element in place, Then he pulled the element out about 3 inches and disconnected the two wires and replace the element with the new igniter put everything back and now its working like a charm

First shut down electric power to oven. remove
oven racks and botton tray. Removed boiler rack and door. Next unscrew 2 bolts holding igniter. remove nuts or cap for two white electric wires.
installed new igniter, hooked backup wires. replaces racks and tray and that was it, job done.

It was easy. I removed the guts. Removed the heat deflector (one nut). Then removed the igniter and the cover over the wires in order to unplug the wires so I could work with attaching the new part on top of the counter. Replaced everything and it worked great. When the old igniter did not work, the gas valve would not let the gas into the oven, Once replaced, you can here the gas flow in and ignite. Repair man wanted $65 to show up and $175 for part and labor. I paid $77 for the part and did it myself. I do not consider myself handy.

It took a while to determine the cause of the problem because I was not familiar with gas appliances.After finding the problem I ordered a new igniter. The part was there in two and a half days!! I had it partly apart when the part arrived so it only took about 30 minutes to complete the repair. I would recomend PartsSelect to anyone. I have never had parts come that quickly.

took off the door it should be very simple by opening the door just a little bit then pull up the door take out the shellves than take of the bottom of oven usualy there's 2 cap screws in back holding it down then take out the drawer from under the oven & unscrew the bracket that holds the flame pipe from underneath also unscrew the screw from inside the oven the holds the actual flame pipe in front next to the door then unscrew the old igniter from the pipe snip the old wire going out from the igniter & strip it a little & connect the new igniter put on the ceramic cover supplied together with the new igniter connect it back to flame pipe put everything back together you should be done. But make sure the wires are pushed down to underneath as much as you could also when you put back the gas pipe the wire should not be in the way underneath the oven

Removed the oven door and the bottom plate. Remove existing igniter by cutting the wire and unscrewing two small bolts. The installation of the new part is the reverse.

I changed out the old ignitor with the new one. New ignitor fit perfect on old mounting bracket. Attached the two wires and that was it.

remove old burner, put new in place

The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.

Removed bottom of oven Removed bottom drawer. Removed two screws holding burner, disconnected both wires.Removed two screws holding igniter,installed new igniter reversing procedure.

Could not get at the screws holding the igniter to the buner, without removing the burner.

I only wish I would have taken the drawer out first to get at the wire connections. Instead I tried to get at them by trying to remove all the layers of sheet metal at the bottom of the oven - to no avail. Once I took the drawer out and saw the connections and bolts to remove that held the igniter/gas diffuser there was no problem. The new igniter does not come with the connectors on the ends so I simply cut off enough wire from the old one and used the wire nuts that came with to splice the wires. Simple reconnect and now we're "cookin' with gas" again.