All Installation Instructions for Hotpoint Range RGB533DEP1WW

lights blown out

replaced lights in refrigirator and freezer

Parts Used:

Light Bulb - 40W

Gerald from WINTERVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 14 people found this instruction helpful.

Was this instruction helpful to you?

The trim piece on the bottom of the door was rusted making the unit look really dirty and used.

It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.

Parts Used:

Bottom Trim - White

Glenn from West Melbourne, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

rusted trim strip

remove screws, re-install screws

Parts Used:

Bottom Trim - White

Larry from Sarasota, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

The eye would not light

Remove the existing burner and install the replacement.

Parts Used:

Burner Head - Large - 12K

Solomon A from COLLEGE PARK, GA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

No ignition

The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had to cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!

Parts Used:

Oven Thermostat

Karen from Dale City, VA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Socket set

6 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Digital clock no longer worked

No longer carry the one to our stove so it was substituted with Nafisa on it. You could see all the electronics so we had to pry the old face off the old one blew it in place, but a clock was reversed from timer, but it works.

Parts Used:

Oven Electronic Control Board

Dolores from AVOCA, IA
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

replaced broken oven door handle

On a 18 year old electric GE range: amazing not the exact handle but it does fit perfectly and looks great. If your somewhat handy this is very easy and can be completed in less than a half hour. Save the screws from the old handle, they can be used again.

Parts Used:

Door Handle

John from BOCA RATON, FL
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

bottom trim had rusted out from water build-up

disassembled bottom trim on oven door.cleaned area of excess rust and installed trim piece.

Parts Used:

Bottom Trim - White

john from buford, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Needed four new burner knobs

Super easy since they just push on. But I wanted to say how impressed I was that I couldn't figure out which knob and sent an email and I got back an email the next day telling me what I needed. Super service! thanks so much

Parts Used:

Burner Knob - White

Judy M from PHILADELPHIA, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

oven racks old and ugly

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired

Parts Used:

Oven Rack

Claudene from ORCUTT, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The light inside the oven had burned out

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Parts Used:

Light Bulb - 40W

Catherine from SEATTLE, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 7 people found this instruction helpful.

Was this instruction helpful to you?

Temp. numbers worn off knob.

Pulled off old knob. Calibrated new knob and pushed it on.

Parts Used:

Thermostat Knob - White

Hugh from PLEASANT HILL, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

The old burners were damaged by the prior owners.

The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.

Parts Used:

Burner Head - Medium - 9500

Burner Head - Large - 12K

Mohammad from BARTLETT, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Burners wouldn't light

Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.

Parts Used:

Burner Head - Large - 12K

Burner Head - Medium - 9500

Robert from SOUTH ELGIN, IL
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

BASE OF BULB BROKE OFF & WELDED TO SOCKET

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Parts Used: