RGB533BEK2BB Hotpoint Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
burner would not light properly and flame uneven around the burner
determined that the top of the burner was melted and malformed. Repair was simple: lifted off the damaged burner and slipped the new one in place.
Parts Used:
-
Bret from South Haven, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven bottom tray would not clean up.Looked like finish was off it
removed two screws and took out bottom tray and put the new one in and replaced the screws.DId it my self.
Parts Used:
-
Jim from 29 Palms, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
11 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Twice I ordered the oven light bulb & each time the light bulb was defected
I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appliance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance
Parts Used:
-
Barbara from BELLEVUE, WA
-
Difficulty Level:Very Difficult
-
Total Repair Time:Less than 15 mins
17 of 36 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
loss of spark to two burners, and bent orifice holder
unplugged the old spark module and plugged the new one in. Disassebled and reassembled the new orifice holder.
Parts Used:
-
Kimberly from Leavittsburg, OH
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
12 of 23 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace Oven light socket and light bulb in kitchen Range
1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and discard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!
Parts Used:
-
Ronald from TUCSON, AZ
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set, Wrench set
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
one burner would not light
opened back panel. noted location of colored wires. disconnected wires & removed module. attache wires to new module & attached module to panel. closed up back panel. tested all burners
Parts Used:
-
joe from malden, MA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
7 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Parts Used:
-
Janine from Wind Gap, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed To Replace Burner
-
Robert K from York, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven would not turn off due to inoperative thermostat
1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.
Parts Used:
-
Timothy from Lake Elsinore, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
7 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old blackened oven racks
-
Roger from Falls Church, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
8 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner on stove not working correctly
Order parts and installed - no tools needed - completed repairs less than 1 minute
Parts Used:
-
Trevor from Eldersburg, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
none
-
Michael from Laughlin, NV
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven ,Going on/off intermittently" Very Dangerous during day /at night especially when all is asleep /away from home,not knowing!
To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."
Parts Used:
-
Leroy-Anthony from Jamaica, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
4 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Hard to remove screws & no instructions that a heat shield had to be transferred from old to new
One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Out of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !
Parts Used:
-
Peter from REDDING, CT
-
Difficulty Level:Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old burner bake tube was burned out in 1 spot.
-
Barry from NORTH BANGOR, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!