All Installation Instructions for Hotpoint Range RGB530DEP1WW

Oven would not turn off due to inoperative thermostat

1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.

Parts Used:

Oven Thermostat

Timothy from Lake Elsinore, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

7 of 13 people found this instruction helpful.

Was this instruction helpful to you?

old blackened oven racks

Replaced old with new.

Parts Used:

Oven Rack

Roger from Falls Church, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

8 of 17 people found this instruction helpful.

Was this instruction helpful to you?

Burner on stove not working correctly

Order parts and installed - no tools needed - completed repairs less than 1 minute

Parts Used:

Burner Head - Medium - 9500

Trevor from Eldersburg, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

none

slid the old ones out and slid the new ones in. done

Parts Used:

Oven Rack

Michael from Laughlin, NV
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Oven ,Going on/off intermittently" Very Dangerous during day /at night especially when all is asleep /away from home,not knowing!

To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."

Parts Used:

Oven Thermostat

Leroy-Anthony from Jamaica, NY
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Broken lines

Super easy!

Parts Used:

Right Front Orifice

Left Front Orifice

David from BONSALL, CA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Pliers, Screw drivers, Socket set, Wrench set

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

bottom trim had rusted, so we needed new piece

Removed oven door (made sure hinges were locked open and stayed open). Remove part on top of trim, removed rusted trim and replaced with new trim. Replaced part on top of trim and screwed all back together. Put oven door back on and unlocked hinges. It was easier than the trial run (when I hadn't realized that the hinges weren't locked open!)

Parts Used:

Bottom Trim - White

Robin from Apple Valley, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

we had damaged the burner cap

just removed the old burner cap and put on the new one.

Parts Used:

Burner Cap - Medium

Gary from Indio, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 7 people found this instruction helpful.

Was this instruction helpful to you?

lights blown out

replaced lights in refrigirator and freezer

Parts Used:

Light Bulb - 40W

Gerald from WINTERVILLE, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

6 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Part rusted over time...22 years.

Unscrewed eight screws. Removed rusted part. Cleaned area with Windex. Replaced new part.

Parts Used:

Bottom Trim - White

Jeannene from HUNTINGTON, TX
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Bottom trim piece on 24 year old stove had rusted. Replace trim piece was still available.

Very simple. Lift oven door off brackets and set on floor. Remove sheet metal screws holding on existing trim piece, Clean area beneath trim.
Put new trim piece on, don't tighten any of the screws until all have been started as some adjustment is needed to align the holes for the screws.

Parts Used:

Bottom Trim - White

Donald from FAYETTEVILLE, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

oven racks very old and writing on knobs worn ff

Very was ti replace racks and knobs. Very fast mail service

Parts Used:

Oven Rack

Patricia from SAN JOSE, CA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

replaced broken oven door handle

On a 18 year old electric GE range: amazing not the exact handle but it does fit perfectly and looks great. If your somewhat handy this is very easy and can be completed in less than a half hour. Save the screws from the old handle, they can be used again.

Parts Used:

Door Handle

John from BOCA RATON, FL
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

The trim piece on the bottom of the door was rusted making the unit look really dirty and used.

It was pretty simple. Just remove the door as the bottom piece holds all the parts together. Place on table top and remove old trim. Install new trim and install door. The only difficult part was the trim had a space for the glass door front. I opened up the space so that the glass would seat easier. Went together real easy. Stove looks like it's brand new.

Parts Used:

Bottom Trim - White

Glenn from West Melbourne, FL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

no problems it was very easy the parts were a perfect match

first you have close the main gas line, then you remove the nut in the center of each burner then you have to push in the two tabs located in the front part of the stove. one on each side of the out side burners. then you lift the top of the stove. then you will need a wrench to loosen the nuts on the tub. then you have to line up the new ones. put the stove top back on then you have to put the nuts on each burner then you can test for gas leaks

Parts Used:

Right Front Orifice