RGB528PEN1WW Hotpoint Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
3 of 4 Burners would not light
Open the stove top pulled old burners out dropped new set in place. Theyclick right in NO TOOLS REQUIRED!!!!
Parts Used:
-
David from Cincinnati, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Parts Used:
-
Patricia from Brandenburg, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
right side burns would not light, if they did it wrapped around outside of burner unit
Pulled old burners out, cleaned area, sat new units in place, made sure they were stable(no rocking), put the top down on the stove and all burners light like new!!
Parts Used:
-
Charmaine M from York, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
both burners were bad
Just opened the box, removed the 2 old burners and replaced with the 2 shiny new ones. Yeah success! I placed my order for this product and before I knew it, it was at my front door. Thank you!
Parts Used:
-
JOHANNA from GERMANTOWN, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
My oven bottom got rusty
I removed two bolts at the rear of the oven bottom. I pulled the old oven bottom out, and put the new oven bottom in. I put the two bolts back in and voila it looks like a new oven. Done in less than 15 minutes.
Parts Used:
-
Mary from Redondo Beach, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!
I needed an oven with three racks, mine came with two.
-
BETTY from CYPRESS, TX
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Burners were dirty and wore out
Unplugged the old ones. Cleaned the stove top. Plugged in the new ones.
Parts Used:
-
Birgit from Opelousas, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
End cap cracked. Tried to fix it with epoxy, but it didn't work.
Used screwdriver w/star bit to remove two screws (longer one on top). Removed cracked end cap. Placed new end cap into position, making sure all tabs were correctly aligned. Replaced screws (top one first)tightening them slowly & alternating back & forth so as not to crack the new part.
Parts Used:
-
William from Lincoln, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
no racks to oven
-
Johnette from Baltimore, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Oven Door Handle Broke
The repair was very easy. It did require a very small torx driver (I can't remember the size off hand.) and a 1/4" nut driver.
Parts Used:
-
Heidi from Carrollton, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Missing oven rack
-
Damaris from Easton, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Oven liner melted....needed to replace bottom
Removed the old oven bottom by removing two nuts. Be careful...don't drop the nuts! Removed the heat shield that was attached with four nuts to the old bottom and transferred it to the new oven bottom. Then placed the new bottom in the oven and secured it with the two original nuts. Easy...but don't forget about transferring the heat shield and don't lose the nuts.
Parts Used:
-
Ruth from Somerset, NJ
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Oven Would Not Turn Off
I read the instructions from other peoples repairs. One note: unplug stove, and turn gas off, remember where wires go. I didnt have to remove top of stove completly.
Parts Used:
-
david from harrisburg, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Numbers removed from knob when cleaned
After receiving the new knob and installing by pulling off the old one and with a little pressure applied, I just pushed the new one into place. With the new knob installed I turned the oven to 350 degrees' putting an oven thermometer into the oven and waited for it to turn off at the end of the pre heat, then matched the knob temp with the thermometer by pulled the handle back off and with the two small screws on back side of handle loosened I adjusted the handle to match the over temperature tighten screws reinstalled
Parts Used:
-
kevin from West Roxbury, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven would not turn off even though knob was turned off.
Unplugged stove. Removed the top rear panel to see where the thermostat cable fed into the oven. Left the current cable in place and fed new cable along side the old one. Pulled out the old cable once new one was installed. Attached wires to new thermostat and installed. Turned oven on to test. Everything went great.
Parts Used:
-
Jeff from Geneseo, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!