RF395PXWN0 Whirlpool Range - Instructions

simply turned off power. took old element out, held in by two screws. pulled out far enough to take off wires. removed and replaced with new element. that was a purfect fit. Works great.

Removed 2 screws holding element in place. Pulled out element to access two wires. Slid off the old element connectors. Placed new element in place and attached the two wires. Pushed it back into place and replaced the screws. Done in 10 min max.

SUPER EASY! The part arrived very quickly. I turned off the circuit breaker, unscrewed the few nuts, pulled out the element and reversed the process. 'works beautifully! Thanks so much.

Simple, just pull out old burners and slide new ones in place. Tried both, they work excellent!

I just had to pull out the old burner and straighten the prongs for the new burner and insert, The prongs of the new burner were slightly bent in shipment, but were easy to straighten with the pliers. The burners were sent in a bag and not a box -- therefore the prongs were easily bent. I was very pleased that I (73 year old lady) was able to fix my stove without a repairman. Saved $$$

took out the old heating elments and cleaned the bottom & top of oven with out the elments in, which made it alot easier then put new ones in. They were very easy to do, just make sure you watch how you took old ones out and don't loose the screws cause you use them to put new ones in.

Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light

First I removed the bottom oven drawer from the stove. Then I removed all the screws from the outer oven door. Then I removed the screws from the inter door panel and needed assistance to remove the first glass panel and frame. Then I removed the second panel of glass and frame. Then I removed the third panel of glass that was broken. The gasket was the last part to be removed. Getting the new gasket to stay put while putting the new glass panel next to it was the hard part. I needed assistance to place the glass against the gasket and then place the frame back on this panel. Once this mission was accomplished. It was a matter of getting the next glass panel put back in the frame. and replacing the inter door panel and putting the screws back in. Then I put the third glass panel and screws back in. Once this was accomplished , I put the outer door back and put the screens back in the outer door.

Lots of screws but if you have the proper sized nut driver it goes quite easily. Take time to see how the inner glass is mounted to the oven door. There are also screws on the bottom of the door that you need to remove to get the inner panel off. The door itself can stay on the hinges

Not only it was easy to install but to find them was even quicker, thanks to Part Select.com. After searching for quite some time I found the site and my problem was solved. Item was received in a timely manner and replacing was very quick.
Thank you.

Unplugged old burner elements. Popped in new burners. Turned on the burners to test.

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

Replaced with the new burner works like new. Thanks a bunch!

The broiler unit had disintegrated at both connections. I removed the two screws in the top of the oven holder the unit, pulled out the unit, measured and ordered a replacement.

To replace the element, I pulled out the stove, removed the rear panel, located the connections for the broiler unit, remove parts of the old unit. I then attached the new unit to the top of the oven with the two screws, went around back and pushed in the two connections, replaced the back cover and replace the stove. It took about 30 minutes because I cleaned everything and sprayed bug spay (another plus for doing the repair myself).

I had to remove the original clips (broken or damaged). This was the hardest part -- the clips were held on by rivets (not screws), so I had to pound/punch them out (using care so not to damage the stove top). Once I punched the rivet out all that remained was a small hole, I just used the small nut and bolt that came with my stablizer clip kit and mounted the new clips. Everything worked out fine.