RF375PXVW1 Whirlpool Range - Instructions

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Plugged in the new burner, which we received in one day.We were delighted with the quick service

Two screws held the element in place, removed the screws and pulled the piece out.
Back of piece has two wires attached, unplug them then attach the new element and replace the two screws to remount.
First make sure the breaker to the range is turned off before starting the repair.

As a former appliance repairman, the installation went just like the repair instruction video.
Just use care not to scratch anything and clean behind the appliance and cabinet walls, etc. It's worth a hug and a piece of pie!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, Removed the old element and installed the new one

Removed 3 screws on bottom edge of door,2 screws on top edge of door. Outside of door comes off. Then use a 1/4 nut driver and remove glass window supports until you get to the inner door glass. Reverse to assemble. Gasket was okey.

Take the time to pull off the door from the hinge; which is to simply pull it up to release with the door open approx. 4 inches. Have a Philips head screwdriver and a nut driver set available. Keep the screws grouped and the take it apart in the logical sequence. It took about 30 minutes total to complete the job. But then again, it was a woman who did it!

simply turned off power. took old element out, held in by two screws. pulled out far enough to take off wires. removed and replaced with new element. that was a purfect fit. Works great.

Removed 2 screws holding element in place. Pulled out element to access two wires. Slid off the old element connectors. Placed new element in place and attached the two wires. Pushed it back into place and replaced the screws. Done in 10 min max.

Unpluged range for safety (power earlier removed by circuit breaker turnoff).
Removed two screws from front switch cover.
Removed knob from effected switch and removed the wires on the back of the switch.
Removed two screws holding switch and removed switch.
Reversed the process to install new switch.
The entire project took about ten minutes.

Simple, just pull out old burners and slide new ones in place. Tried both, they work excellent!

I just had to pull out the old burner and straighten the prongs for the new burner and insert, The prongs of the new burner were slightly bent in shipment, but were easy to straighten with the pliers. The burners were sent in a bag and not a box -- therefore the prongs were easily bent. I was very pleased that I (73 year old lady) was able to fix my stove without a repairman. Saved $$$

SUPER EASY! The part arrived very quickly. I turned off the circuit breaker, unscrewed the few nuts, pulled out the element and reversed the process. 'works beautifully! Thanks so much.

First I removed the bottom oven drawer from the stove. Then I removed all the screws from the outer oven door. Then I removed the screws from the inter door panel and needed assistance to remove the first glass panel and frame. Then I removed the second panel of glass and frame. Then I removed the third panel of glass that was broken. The gasket was the last part to be removed. Getting the new gasket to stay put while putting the new glass panel next to it was the hard part. I needed assistance to place the glass against the gasket and then place the frame back on this panel. Once this mission was accomplished. It was a matter of getting the next glass panel put back in the frame. and replacing the inter door panel and putting the screws back in. Then I put the third glass panel and screws back in. Once this was accomplished , I put the outer door back and put the screens back in the outer door.

took out the old heating elments and cleaned the bottom & top of oven with out the elments in, which made it alot easier then put new ones in. They were very easy to do, just make sure you watch how you took old ones out and don't loose the screws cause you use them to put new ones in.