RF3600XYN2 Whirlpool Range - Instructions

Turn off the power, removed the two screw (needed a wrench to help turn screw driver at first). Pulled the element forward to expose the wire connectors. Removed connectors from the old element. iInstalled new element to the wire connectors (slide on), screwed plate back into oven. Turn on power and tested

Unwrapped package. That was the hardest part. Inserted into the little spot on top of stove. Tested. Worked great!

Easy unplug appliance take racks out unscrew two screws gently pull out element unplug two wires put new one in reverse .

Shut off power to the stove.
I removed the screw that held the block in place. Then I lifted the top of the rage to get to the wires. I cut the wires from the old block and stripped back the insulation. Next I put the heat shrinking sleeve on. I attached the new block with the wire nuts, pulled the sleeve down and used a hair dryer to shrink them. Then you just hook it back on screw it in and your done.

I took the old wires and plug off and replaced it with the new block it works fine

turn off electric breaker, unscrew the 2 screws unplug the 2 ends replace old element with new repeat previous steps but unfortunately the control panel was also failing and that item has been discontinued.

Locate and shut off 220 volt breaker to Stove/Oven. Remove baking racks from oven. Use phillips screw driver to remove two phillip head screws holding bottom baking element in place. Slowly pull out element/wires and use volt meter to check for presence of voltage. Remove wires from element by pulling off female spade connector, push wire connector onto new element, carefully push wiring and element end thru rear opening and secure with the two phillip head screws. Replace baking racks, turn 220 volt source back on and test element to a high temperture, leave oven door open, new element will smoke slightly and create a burning odor, so take a few minutes to break in the new element. You're now readly to bake.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Repair was very east. The suppliers package had all of the necessary parts ceramic wire nuts wire Ect. Excellent.
Will buy from Part Select Appliance again.

remove burned out eye, replaced with new eye.new eye does not fit exactally correct onto splash pan as point on end of steel " rod " not pointed enough to slip into mate on splash pan

Took a phillips head screwdriver and took out the two screws. Lifted off small plate securing screws, pulled lightly and wiggled the element out and popped the new one in. Total time 7 minutes - yes we timed it!!! Fast delivery too!!!

I removed the block, cut and spliced the wires to the new block and installed the burner. I used the new style block kit and saved about $30. It worked great!

Disconnect power to the oven at circuit breaker. Most important confired power removed by turning on buner,also with electrial meter. Remove hex screw. Pulled purner forward approx 3 inches remove the two wires to burner element . Installed new burner reverse rotation . Returned power to oven,all was well no problems. Not to sure of burner wattage on old and new unit,as two burners are avaiable for this unit. All ok . Thanks to parts select for speedy part needed

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

lifted up burner and pulled it free from its connection, then removed drip pan. used my cordless drill to drill out broken stabilizer clip. cleaned up chips from the drill process before installing new clip. installed clip with enclosed screw and nut. I then installed the new burner by lining it up with the connection under the cook top pushed it place and lowered it into the stabilizer clip. Then I turned the burner on to try it out, but I waited for about one hour before turning on the burner because it was cold from being outside.