RF3000XPW0 Whirlpool Range - Instructions

I used the replacement video from the web site. The replacement went great.

Removed all surface burners from range, removed range top screws, and suspended range top. Removed plug-in block mounting screw. Cut wires for plug-in block close to original wire-nut junction. Inserted contacts & wires from kit into plug-in block. Slid a provided shrink sleeve onto each wire. Stripped wires on range wires and then connected them to the plug-in block wires with the provided high-heat wire nuts. Selected one of the two provided plug-in block brackets that matched the original bracket on the range. Used a butane lighter to shrink the shrink sleeves over the wire nut connections. Snapped the appropriate bracket onto the plug-in block. Reassembled everything in reverse order and plugged in new element. Note: my only two issues are that the two high-heat wire nuts provided in the kit were a bit too small for the wire gauge in my Whirlpool range. It took some fiddling on my part by carefully re-stripping the range wires to get the wire nuts twisted on securely. Two more wire nuts of the next size up would have been appreciated. Also, I found that the provided plug-in block mounting screw did not find fit my range. No problem; I simply re-used the original screw. All in all, an easy repair and the element works perfectly.

I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.

Just like you said,remove two screws,pull out element,disconnect wires,install new part. It was easier to pull out stove and hook up wires.

Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!

Super simple, and the part arrived less than 48 hours after buying it online. I turned off the breaker to the oven and unscrewed the burner at the bracket holding it to the back wall of the oven. After pulling out the wires, all you do is tug at the two connectors and they detach. Just slide the new burner's connectors in, then screw it back into place. My arms aren't quiet long enough to reach all the way back there, so I got my son to help and I held the flashlight for him. Had it done before my husband got home from work!

I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.

Now I know why everyone said "less than 15 mins" for installation time...because "less than 5 min" wasn't an option! Went exactly as everyone described, just more quickly - turned off breaker, removed two screws, disconnected wires, reconnected wires to new element, re-attached it with screws, turned on breaker, checked it - worked like a charm. It was more work opening the box! Would have taken less time if my flashlight hadn't rolled off the open oven door leaving me with poor lighting conditions.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
then I reconnected the two wires to the new element and put back the two screws that hold the element in place and the job was finished.

Turned off circuit breaker for oven. Unscrewed the 2 screws that held the element in place on the back wall of the oven. Save those screws! Pulled the element out from the wall. Disconnected the 2 wires. Attached the wires for the new element and then screwed the new element into the back wall. Flipped the circuit back on and the oven was fixed.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

Disconnect power to the oven at circuit breaker. Most important confired power removed by turning on buner,also with electrial meter. Remove hex screw. Pulled purner forward approx 3 inches remove the two wires to burner element . Installed new burner reverse rotation . Returned power to oven,all was well no problems. Not to sure of burner wattage on old and new unit,as two burners are avaiable for this unit. All ok . Thanks to parts select for speedy part needed

I took out the coils manually by pulling them out with slight pressure. Then I lift the hood by first unscrewing the four screws. I have never done anything like this before just intuitive sense to locate the screws that needed to be loosened. Afterwards I remember placing something underneath like a piece of 2x4 wood block to act as support to hold the hood open so I can work on the coils. The parts I got are exactly the same as those I am replacing so I just copied the connection and voila my electric range is working like new. Well of course before I touched anything, I made sure I turned off the main switch and that nobody switches it back on without my knowledge. Thanks for providing the parts, I just saved myself from buying a $600 electric range.

Locate and shut off 220 volt breaker to Stove/Oven. Remove baking racks from oven. Use phillips screw driver to remove two phillip head screws holding bottom baking element in place. Slowly pull out element/wires and use volt meter to check for presence of voltage. Remove wires from element by pulling off female spade connector, push wire connector onto new element, carefully push wiring and element end thru rear opening and secure with the two phillip head screws. Replace baking racks, turn 220 volt source back on and test element to a high temperture, leave oven door open, new element will smoke slightly and create a burning odor, so take a few minutes to break in the new element. You're now readly to bake.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.

turn off electric breaker, unscrew the 2 screws unplug the 2 ends replace old element with new repeat previous steps but unfortunately the control panel was also failing and that item has been discontinued.