RF260BXSW1 Whirlpool Range - Instructions

Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element

It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.

Repair of oven sensor easy to install; however, product did not resolve the problem. Returned new sensor and awaiting refund (2 weeks passed so far).

it took 2 people to do this job. we had to place a yard stick inside the door to keep it open because after we removed the 2 screws inside the door that held the handle on, the door would not stay open. after removing the handle we had to slide the glass down from the top and line it in the slots at the bottom and then we had to replace the handle back on top of the stove, lining up the slots and the side pieces. after that we screwed in the 2 screws and yea! we did it right. The glass is in and we managed to not break it!

1) Unplug stove.
2) Remove back cover of the stove held in place by 8 screws (4 short ones for the upper holes and 4 longer ones for the lower holes.).
3) Remove the knob from the switch that you are replacing to expose
the switch mounting screws (2 screws).
4) Remove the screws.
5) Go to the rear of the stove and extract the defective switch.
6) You will see 2 plastic plugs going into/onto the switch. Remove the
plugs. MAKE SURE YOU ARE UNPLUGGED FROM THE
Wall OUTLET!! A small flat blade may be needed to separate the
plugs from switch.
7) Attach the plugs to the new switch (there is only one way to do it.
you wont get them confused and put on wrong.
8) Put the new switch where the defective one was.
9) Come to the front of the stove and put your two screws in and
replace the knob.
10) Replace the back cover,
11) Plug in and test burner.

Unplugged stove from electrical outlet. Pulled temperature control dial off by hand. Remove screws to top back stove panel with Phillips screwdriver. Removed top stove back panel. Unscrewed broken infinity switch from stove. Unclipped wiring harness to broken switch by prying loose with flat head screw driver. Reclipped wiring harness to new switch. Screwed replacement switch back onto stove. Reattached back panel with screws.

Lift and remove heat elements
Lift and remove Drip bowls

Replace Drip bowls and heat elements

My husband pulled the oven out and unscrewed the screws(in the back) the heating element came right out. He did everything on his own. The only thing he needed a little help with was for me to keep the heating coil flush to the back wall of the oven, while he screwed the new one in. It was a very quick job. The longest part was pulling the oven out to get behind it and sliding it back in.

Wire connection was damaged, replaced end piece

After unplugging electric service, loosened 3 Philips-head screws holding 3 wires from range and loosened 3 nuts holding wires from electric cord. Also removed 1 Philips-head screw holding grounding tab. Removed 2 Philips-head screws and removed the old block. Mounted new block with those screws and replaced and tightened all 6 wires.

Very easy remove the burner and instill the drip bowls

My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed old terminal block & replaced with new one. Very simple. Did NOT have to replace cover as stated you should. Shipping could have been a little faster. Will definetly try this site again.

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too