All Installation Instructions for Whirlpool Range RF111PXSW2

element went out on the stove

My wife did it! I got home one night and my wife had done it! That's how easy it was! Trust me, he is no handyman (woman) but she did it by herself. The part came fast, the price was better than any one else's

Parts Used:

Oven Bake Element

christopher from harrisburg, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 7 people found this instruction helpful.

Was this instruction helpful to you?

light bulb in water ice freezer door went bad

I didn't. Don't know how to get to light bulb to change it for this specific model

Parts Used:

Light Bulb - 40W

Carl from RIVERSIDE, CA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

7 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Oven sensor was not regulating heat set for oven

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

Parts Used:

Oven Sensor

Linda from SAINT CLOUD, MN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Electric contact connection melted, shorting out the range.

After unplugging electric service, loosened 3 Philips-head screws holding 3 wires from range and loosened 3 nuts holding wires from electric cord. Also removed 1 Philips-head screw holding grounding tab. Removed 2 Philips-head screws and removed the old block. Mounted new block with those screws and replaced and tightened all 6 wires.

Parts Used:

Terminal Block

Vincent from SHILOH, IL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Block had melted.R

Removed old terminal block & replaced with new one. Very simple. Did NOT have to replace cover as stated you should. Shipping could have been a little faster. Will definetly try this site again.

Parts Used:

Terminal Block

Thomas H. from COCOA, FL
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

I broke a piece of the trim and had to replace it

took the handle off, replaces the side trim piece and replaced the handle. Very simple!

Parts Used:

Side Trim - Right Hand Side

Gregg from SOUTH BEND, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Generic drip bowls in the stores did not fit

Very easy remove the burner and instill the drip bowls

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Elaine from BROAD BROOK, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

temp sensor went oven not heating

the hardest part was moving stove to trplace part

Parts Used:

Oven Sensor

patrick from HUGHESTOWN, PA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

bottom piece of range rusty

took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one

Parts Used:

Range Trim Lower (White)

Bruno from LE ROY, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

4 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Broiler element not working

It went great. I am not very handy, but with a little help from your website reviews, I was able to easily remove the old broiler element and replace it with the new one in less than an hour. I immediately tested it and found that it worked great.

Parts Used:

Broil Element

Normand from Lincoln, RI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

6 of 11 people found this instruction helpful.

Was this instruction helpful to you?

The oven was blowing a circuit.

Unplugged unit from wall.
Unscrewed the two screws on at he back of the oven where the element is attached
Removed old element by pulling apart the connectors.
Attached new element to the connectors.
Replaced cover with the two screws.

Parts Used:

Oven Bake Element

Rhonda from Logan, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

5 of 9 people found this instruction helpful.

Was this instruction helpful to you?

had for 2 weeks didnot work called for warinty they fixed stoped woking again about 18months later called them got price then bought though you.

first i turned off breaker . then slid out stove .usea cordless screwdriver totake off back then unplug switch then take off knob then take screwes out of front of switch theninstall new one revice method. took me longer to do this then to do the part

Parts Used:

Range Temperature Switch 240v

frank from pittsburg, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

8 of 18 people found this instruction helpful.

Was this instruction helpful to you?

Broken rear stove drawer glide

Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

Parts Used:

Range Rear Drawer Glide

John from Maysville, GA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Oven Temp inaccurate

I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!

Parts Used:

Oven Sensor

David from BURNSVILLE, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

3 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Burned out wires and 2 switches.

Unscrewed the switches and let the switch hang while replacing one wire at a time. Followed instructions on wire replacement. Exact parts, only shaft on 6" switch was too long -- okay, because it is designed to break off a piece on end of shaft, then the knob fit. Everything was perfect.

Parts Used: