RESF3330DB Samsung Range - Instructions

1. Turned off power at breaker, 2. removed two screws holding cooktop (located at top of oven in door seal area), 3. removed 4 set screws holding burner in place, 4. Removed wired (blade connections) one at a time and moved to new burner, 5. installed set screws to hold burner in place, 6. lowered cooktop and reattached screws to hold in place, 7. turned breaker back on.

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.

Parts package contained no instructions. Found all instructions on internet. I used Phillips head to remove two screws on anchor plate of Long Oven Sensor. Located at upper left, back corner of oven; access to screws is not simple/easy. Screws back out w/o difficulty. Pull/extract sensor harness through hole[back of oven] which required pushing aside insulation. The harness barely fits thru hole in oven back metal wall; I recommend using needle nose pliers ( which I ended up doing ) for ease of extraction. Disconnect harness plastic interlok clips. Perfect reconnection of new clip harness with ease. Reverse procedure to complete installation/repair. Done in just over 35 minutes due to wrestling with harness extraction through minimal hole opening. Failure occurred on Thanksgiving Day with 22lbs turkey in oven. Top of turkey contacted sensor tip which eventually caused sensor fault; result was scorched upper breast and oven shut down [safety by design]. Cook top was still operative; clock and all readings on digital control panel ceased. With new 'long oven sensor' installed - good as new. Will be sure to buy turkey(s) under 20lbs in future. Jim in Seattle

Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.

Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.

Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)

Ordered a front burner but it was not the right size. Ordered a switch after local dealer said I had a bad switch. Ordered a switch from Parts Select and received it the next day. Works good now.

I ordered both the light bulb and the switch that controls it. I had not pulled the stove out because the ones I bought this house from did not level the floor which meant I had to wait on a socket set to arrive in order to be able to pull my stove away from the wall. Once I got the socket set and the stove out I removed the panel on the back. I saw then that my red light bulb had shattered in half forcing the switch to just hang free. Glad I had ordered both parts, removed the old, replaced new with ease... then it was a matter of sliding the panel back in place without the main control panel getting misaligned, few trial and error checks and it went back with ease. New light works! Very easy.. probably less time if your floor is level.. then I had to play with the little legs to get it even again. For now it is ok until the spring where I go to redo the floor and make it all LEVEL! Very easy! Hope it doesn't burn out again but if it does I know what to do! Maytag rep wanted to charge me $100... No thanks!

The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

We took the back off the stove and unscrewed the two screws from the inside holding the sensor on and pulled it through and plugged it in and then replaced the screws. Very easy. We are still having trouble as the display does not read the same as the tempature is in the oven.

Turn off power 220v, opened cook top, remove old 8" switch and replace with one of the new switch ps2089438. However, I have another cook top, it is a 6" heating element. Can I use the same switch for 8" and use on a 6" heating element? Since I order 2 new ps2089438 switches. Thank you for your anwser. Kahn lee

Pulled stove out to unplug. Removed screws holding end covers then remove screws on the underside of cover as you face the stove top.Remove knobs.Pull bottom cover forward and up so you can lift it off to see the insides.Remove wires and attach to the new part one at a time. Unscrew old from the front and attach the new one.Put it back together.Done.

Followed video