REP302M1W Gibson Range - Instructions

Moved stove out from wall and cabinets, then unplugged the stove. Removed the oven racks, then removed the 2 screws securing the baking (lower) element to the rear wall of the oven. Pulled the element out a few inches and disconnected it from the stove wires. Removed old element. Removed screws from rear panel to gain access to wiring. Inserted new element and connected to wiring. Put element in place and replaced the 2 screws in rear wall. Put rear panel back in place and replaced panel screws. Plugged stove back in and moved back into place. Tested oven and it worked just fine. Parts Select did a great job of filling my order and promptly shipping it. I got it in 2 working days.

Removed the elments2 screws, unhooked the two wires, removed the rear cover from back. I then installed the new element, covered the termanals with electric tape replaced the rear cover screwed down the new element, tested.

took off the back of the stove..first Unplugged it! and undid the old unit, and put the new one on....easy peasy!..Thanks for your fast mailing!

Turned off main power at electrical breaker. With pliers, removed two screws that hold element in place. Pulled element out about 3 to 4 inches. Disconnected two wires from element. With pliers, adjusted connections on new element connections from horizontal to vertical position. Connected two wires to connections of new element. Installed new element in oven with original two screws. Powered on main electrical breaker. Oven back in operation! Also, part arrived in 3 days! I'm a happy camper!

took out the screws at the back of the oven, removed the old element and put the new one in, replaced the screws. The new part was mostly the same size as the old one, some of the angles were different and the ends slightly different, but it fit and works great.

Loosened two nuts , removed old element. New element snapped into terminal tightned nuts . 0 minutes tops.

I removed the 2 screws. Pulled the heat elemnet out. Disconnected the 2 wires. Then I connected the 2 wires to the new element. Pushed it back in. Tightened the screws and was sone.

My husband completed this replacement in less then 5 minutes. He took out two nuts discounected the old element then replaced with the new element. Easy!

Removed two screws that hold the element in place. Pulled it out a few inches-removed the wires
& re-connected to the new unit. Screwed it back in place & i was done. It took about 10 minutes. The new unit works fine. Saved a bunch of money by not calling a repair man. Thank you very much.

Unplugged range and cut wires on existing burner plug. Connected the replacement plug with the provided wire-nuts. Secured with provided shrink-wrap. Reattached burner plug to to range top, and plugged in the burner coil. Presto.

Oven quit heating after less than 6 years. Checked with a volt-ohm meter and determined element was open. Ordered new element. Unit arrived in good time, replaced in about 15 minutes with no problems at all. Took longer to remove and replace oven door tha it did to install element.

Locating part on web site, ordering, receiving next day & installing was very very easy. Information provided on PART SELECT web site and that provided with part made this a very easy and cost effective repair. With service provided by PART SELECT there is no reason to pay for an expensive service call in addition to what a repair company would charge for the part.

Thank for having the part necessary to put the old range back in shape. The repair job was simply to unplug the old one and plug in the new one! Great simply job!

Unplugged stove, use nutdriver, removed screws, pulled out old element, put in new one. Done. As prescribed. Excellent help as well as got part the next business day.

took me longer to find my 1/4 inch nut runner and drill than to change out the element.........simpliest replacement i've ever encountered and i'm 64 years old. less than 2 minutes......